Log entry time 10:53:15 on May 30, 2002

Entry number 4253

Beginning-of-run EPICS data for Run Number 1022 at Thu May 30 10:52:55 EDT 2002
; (Integer!) prescale factors for runs. 
; This file is read at start of every run.
; Do NOT put spaces in string, NOR add 2nd string. (REALLY!!!)
; The default factor is essentially infinite. 
; ps8 = 65535 turns off the 1 kHz pulser on T8.
; Keep enough T2 and T4 to measure efficiency
; PS1 for the Right spectrometer based on T1 defined by S1*S2
; PS2 for the Right spectrometer based on T2 defined by S1+S2
; PS3 for the Left spectrometer based on T3 defined by S1*S2
; PS4 for the Left spectrometer redundant trigger T4 S1*S0+S2*S0
; PS5 for coincidence of T1 and T3.
; PS7 irrelevant
; PS8 for pulser 
ps1=1,ps2=1000,ps3=1,ps4=10,ps5=1,ps6=65535,ps7=65535,ps8=65535
 
Left Arm Q1 power supply current : 1918.88
Left Arm Q1 momentum : 2.55057
Left Arm Q1 gauss meter : -0.16215
Left Arm Q1 power supply polarity : 0
Left Arm Q2 power supply current : 1600.05
Left Arm Q2 momentum : 3.71585
Left Arm Q2 gauss meter : 0.842
Left Arm Q2 power supply polarity : 1
Left Arm D1 power supply current : 880.108
Left Arm D1 momentum : 2.55004
Left Arm D1 NMR : 0.943877
Left Arm Q3 power supply current : 1600.02
Left Arm Q3 momentum : 4.01894
Left Arm Q3 gauss meter : -0.8001
Left Arm Q3 power supply polarity : 1
Right Arm Q1 power supply current : 1917.41
Right Arm Q1 momentum : 2.54996
Right Arm Q1 gauss meter : -0.04757
Right Arm Q1 power supply polarity : 0
Right Arm Q2 power supply current : 1400.16
Right Arm Q2 momentum : 3.25341
Right Arm Q2 gauss meter : 0.7347
Right Arm Q2 power supply polarity : enabled
Right Arm D1 power supply current : 419.188
Right Arm D1 momentum : 0
Right Arm D1 NMR : 1.8838
Right Arm Q3 power supply current : 1400.03
Right Arm Q3 momentum : 3.51847
Right Arm Q3 gauss meter : 0.6279
Right Arm Q3 power supply polarity : disabled
Left Arm Top VDC Current : -2.58789
Left Arm Bottom VDC Current : 2.39258
Right Arm Top VDC Current :
Right Arm Bottom VDC Current :
Average current of the two cavities : 0.0331227
Current on Unser monitor : 4.49887
Current on Upstream bcm : 0.0368647
Current on Downstream bcm : 0.0293808
Upstream Cavity Coefficient : 77.4
Downstream Cavity Coefficient : 79.06
Current on IBC0L02 (source) : 0.00143682
Tiefenbach Hall A energy : 2844.26
Tiefenbach Hall C energy : 4705.57
Delta(E)/E width (MV_AI_DXWID) : 3.95114
MBSY1c Hall A Beam energy : 2849.17
MBSY3c Hall C Beam energy :
MBSY1c magnet current (amp) : 118.6
MBSY1c Bdl : 711013
Arc1 dp/p : 1.12201e-05
Arc2 dp/p : -0.000674745
Left Arm Arm Collimator : 0.61958
Left LVDT HPM : 1361
Left LVDT VPM : 700
HacL_HPE1313A:0_Ch58 : -0.132324
HacL_HPE1313A:0_Ch55 : 22.6074
HacL_HPE1313A:0_Ch54 : -0.115723
HacL_alignROLL : 0.231513
HacL_alignPITCH : -0.125067
HacL_alignHPT : -0
Left Arm Angle Floor Angle : 19.5
Left Arm Angle Vernier : 57.2
Left Arm Scattering Angle : 19.6507
Right Arm Arm Collimator : 0.612061
Right LVDT HPM : 1066
Right LVDT VPM : 211
HacR_HPE1313A:0_Ch58 : -0.529785
HacR_HPE1313A:0_Ch55 : 21.1914
HacR_HPE1313A:0_Ch54 : -0.832031
HacR_alignROLL : 0.466989
HacR_alignPITCH : -0.489172
HacR_alignHPT : -0
Right Arm Angle Floor Angle : 19.5
Right Arm Angle Vernier : -8.2
Right Arm Scattering Angle : 19.6497
IPM1C12.XPOS :
IPM1C12.YPOS : 0
IPM1H04A.XPOS : 0
IPM1H04A.YPOS : 0
IPM1H04B.XPOS :
IPM1H04B.YPOS : 0
Survey X offset bpmA : -0.63
Survey Y offset bpmA : -0.9
Survey X offset bpmB : 0.77
Survey Y offset bpmB : -1
Target OTR x-position : -7.9589
Target OTR y-position : 7.73516
Target OTR x-width : 0
Target OTR y-width : -0
Target OTR data valid flag : No
Target OTR In/Out : Current is Low
Arc OTR x-position : -1.94539
Arc OTR y-position : 0.244755
Arc OTR x-width :
Arc OTR y-width : 1.96821
Arc OTR data valid flag : No
Arc OTR In/Out : OTR is Out
Current Setpoint : 0
Current Readback : 0
fan frequency loop 1 :
fan frequency loop 2 : 24.5
fan frequency loop 3 : !!WARNING!! The executable "caRepeater" couldnt be located because of errno = "No such file or directory" You may need to modify your PATH environment variable. Creating CA repeater with fork() system call. Repeater will inherit parents process name and resources. Duplicate resource consumption may occur. 0
Encoder position : 163854
temperature loop 1 : 22
temperature loop 1 : 22.23
temperature loop 1 : 21.84
temperature loop 2 : 19
temperature loop 2 : 18.99
temperature loop 2 : 19.19
temperature loop 3 : 89.9
temperature loop 3 : 72.68
temperature loop 3 : 94.98
pressure loop D2 : 28.1361
pressure loop H2 : 26.5431