Log entry time 22:13:03 on November 29, 2011

Entry number 359513

This entry is a followup to: 359426

Followups:

• 359518 11/30/11 09:59 A. Camsonne Test code for TS in /adaqfs/home/a-onl/ts_test

I looked a bit with Pengjia at the EB1 seg faulting.
It seems the TS always misses the end event.

We removed Happex crate from the branch of the TI of the TS and put
resistors there and ran the configuration with ROC2 and TS only but we
still saw the same problem.

Problem does not occur for a few hundreds of events using T1.

Though it always happen above 1000 events according to Pengjia.

I check the fastbus TI resistors and they looked fine.

We also changed the ribbon cable just in case. But we still have the issue.

I will try to make a configuration with only TS0 though right now my
config does not take any trigger when only TS0 is there.

Still same errors as previous log entry :

TS roc selection is for TS ( HW ROC 0 ) and ROC2 ( I guess HW ROC 2 but
did not double check switches )

daLogMsg: INFO: Entering User Prestart 2
linking sync EVENT trigger to id 1 
daLogMsg: INFO: User Prestart 2 executed
rolp->daproc = 2
daLogMsg: INFO: Entering User Prestart
Linking sync VME trigger to id 1 
daLogMsg: INFO: rscale is on 

daLogMsg: INFO: FTM csr at 0xfbff0ed0 is programmed for 0x35 

Config disable=0 psevent=0 tsreadout=0 
Right Arm TS Control -- Roc Selection 1000004
Trigger register setting = 0x101 
daLogMsg: INFO: Prescale trig 1 = 0  trig 2 = 0

daLogMsg: INFO: Prescale trig 3 = 0  trig 4 = 0

daLogMsg: INFO: Prescale trig 5 = 0  trig 8 = 1

-------------------------------------------
Event builder

Broadcast message from a-onl (pts/2) (Tue Nov 29 22:03:34 20
11):

ok
daLogMsg: INFO: prestart
EB1 has 2 input links
last ROC is 2
last ROC is 10
open links
daLogMsg: INFO: Prestarting (C)
et init 1
deb ET init: ET fully initialized
daLogMsg: INFO: deb prestart: ET is alive - EB attached
Create build thread
events per token 64
daLogMsg: INFO: prestarting,run 20490, type 3
daLogMsg: INFO: link ROC2->EB1 connected as file8 to 129.57.
192.24
daLogMsg: INFO: link TS0->EB1 connected as file14 to 129.57.
192.28
Got control event fragments type = 17  node_ix=2
Build control event: prestart(stream0, stream1)
-- Got all fragments of prestart
daLogMsg: INFO: Activating (C)
Got control event fragments type = 18  node_ix=2
Build control event: go(stream0, stream1)
-- Got all fragments of go
daLogMsg: FATAL: Event (Num 105 type 8) NUMBER mismatch -- s
tream1 (rocid 10) sent -1 (type 20)
daLogMsg: ERROR: Discard data until next control event
daLogMsg: WARN: Found sync point 20 for ROC stream1
socket 14 closed
thread exit for TS0
daLogMsg: WARN: Found sync point 20 for ROC stream0
daLogMsg: WARN: Resyncronised via control event
got all end events!!!!
ROC mask 1028 force_end 3
Segmentation fault

------------------------------------
Component: 'ROC2' Object: 'ROC'
Readout list names: 'rol0 rol1'

ROC state         :        6, Active Level       :        1
End Range         :        0, Last Event Sent    :    24425
Run type          :        3, run number         :    20490
Event Number      :    24425
rol1 events       :        0, rol2 events        :        0
clear to send     :        0, dataInBuf          :       12
g_events_in_buffer:        0, g_max_ev_in_buf    :     1797
message queue     :        0, outputQueue        : 1ebdc270

---------------------------------------



omponent: 'TS0' Object: 'TS'
Readout list names: 'rol0 rol1'

ROC state         :        6, Active Level       :        1
End Range         :        0, Last Event Sent    :    24424
Run type          :        3, run number         :    20490
Event Number      :    24424
rol1 events       :        0, rol2 events        :        0
clear to send     :        0, dataInBuf          :       12
g_events_in_buffer:        0, g_max_ev_in_buf    :     1797
message queue     :        0, outputQueue        :  7357750