PVDIS How To Page

• Troubleshooting (note: link is working again)

• In the production mode of this experiment, the PVDIS DAQ is a combination of the PVDIS electronics and the HAPPEX DAQ. The HAPPEX DAQ is used to readout data. Periodically, we also use the HRS data acquisition system for systematic studies.

• HAPPEX/PVDIS Data Acquisition (Updated [date])

  • Use the checklist when switching DAQs
  • Cold start
  • Monitoring HAPPEX systems
  • Turning Dithering on/off
  • Rebooting HAPPEX crates
  • List of HAPPEX crates
  • Running CODA
  • Switching CODA config (between Happex & HapNoQweak)

• HAPPEX Data Analysis (Updated [date])

  • Starting Online Data Monitor
  • Starting prompt analysis

• Spectrometer

  • Bringing up the Alarm Handler
  • Bringing up the HAC control window
  • Changing momentum setting of HRS and Septum
  • Reset Q1 of Left or Right HRS

• Target

  • The best reference for all things target is The Hall A Cryogenic Target home page
    
  • Checking target temperature
  • New procedure for target IOC reboot (New!)

• Spectrometer Data Acquisition

  • Use the checklist when switching DAQs
  • Cold start
  • Mapping of ROCs to portserver and IP
  • Spectr. DAQ Triggers for HAPPEX
  • Rebooting HRS crates
  • Running CODA
  • Starting xscaler (HRS) and checking trigger rate

• Spectrometer Data Analysis

  • Online analysis

• Hall A Detectors (Updated [date])

  • List of Detectors
  • Detector High Voltages
  • VDC check and HV

• Compton Polarimeter

  • Compton Polarimeter Home page.
  • Compton Data-Taking instructions.
  • Compton Logbook (analysis results)

• Helicity Controls (Updated [date])

  • Changing the Half-WavePlate
  • PITA Scan
  • HAPPEX Charge Asymmetry Feedback

• Miscellaneous

  • Bringing up the Beamtime Counting Table
  • Plotting time dependences of EPICS variables
  • Printing in the counting house
  • (Updated 9-23-09)Starting HALOG
  • Starting spot++ and checking the raster

• Other Problems

  • If you can't solve a problem

HAPPEX/PVDIS Data Acquisition

HAPPEX DAQ cold start (up to date as of 10-28-09)

Note: This is for HAPPEX DAQ. If you want to cold start spectrometer DAQ see Spectrometer DAQ cold start.

• If switching from Spectrometer to HAPPEX DAQ, you must turn off detectors that can be damaged by high rate before turning on high current beam; for PVDIS this means the VDCs. Use checklist when making this switch.

• Do the following at a shell prompt on adaql1 on the apar account. This does a kcoda, etc, for you:

  > startcoda
  

• The Runcontrol GUI will start up. Now click on the Connect button.

• Wait 10 seconds, then click on Configure. A dialog box pops up and you must choose the configuration you want, which is presumably HAPPEX.

 

              List of Useful DAQ Configs 

 All these can be used for the experiment.  Ask the RC which is preferred at the moment.

   Happex -- Full config, all crates.
   HapNoQweak -- Full config minus the Qweak crate (it's less important and may have crashed)

 The following should not be used for PVDIS:
   HapNoPvdis -- Full config minus the PVDIS crates (ditto).
   HapSimple -- Full config minus Qweak and minus PVDIS.  Minimum needed for HAPPEX-3.

• Wait for configuration to finish (see messages in text box at lower left), then click Download.

• Wait for that to finish. Now you can click Start Run to start a run (see section on Running CODA).

• In another workspace, open up xterms for monitoring the ROCs by starting the ROC IT GUI:

  > roc_it

  Click on OPEN ALL. An xterm should open for each IOC. If you are asked for a login name, use adaq as the user. The password is the same as in the counting house computers.

Turning Dithering on/off (up to date as of 9-23-09): dithering should be on throughout the PVDIS running.

• Log in if necessary to adaql1 on the apar account

• Bring up a greenmonster terminal by typing

  > greenmonster

• On the GreenMonster gui, click on BMW tab

• To check the current dithering status, click on

  > Check Status

• If the dithering is turned on , then Beam Modulation is ON is displayed to the right of Check Status tab. The tab to the left of Check Status tab will appear as Set Kill Switch, with Kill Switch is OFF message displayed above it.
• If the dithering is turned off , then Beam Modulation is OFF is displayed to the right of Check Status tab. Dithering can be turned back on by simply clicking

  > Enable Modulation On

• Ensure that the dithering is turned on by clicking

  > Check Status

• NOTE If reboot the parity daq crate (ROC 23, halladaq6, hatsv9 2004) you will need to restart dithering!

Monitoring HAPPEX systems (up to date as of 9-23-09)

• Log in if necessary to adaql1 on the apar account

• To check status of feedback system and polarized source, type at shell prompt:

  > runbird

  Help is available using the Help button at the bottom. Settings and numbers to expect can be found in the White Bound Shift Worker Folder.

• To set/check status of HAPPEX ADCs and timing boads, type at shell prompt:

  > greenmonster

  Click on tabs at top to examine ADCs in different crates or timing. <- this should be updated for PVDIS (no HAPPEX det ADCs)

Rebooting HAPPEX crates (up to date as of 9-23-09)

• If a run is in progress, end it. If you can't end it, close the CODA GUI window.

• There should be xterms open for each roc in the ROCS workspace. In the desired xterm, click ENTER a few times to check communication to the IOC. Then type:

  > reboot

• The IOC will then proceed through its booting sequence. It is ready when either of these messages appear (e.g. for ROC23/halladaq6):

  "ROC23" state now "booted"
Done executing startup script /adaqfs/halla/apar/vxworks/halladaq6.boot

• In the runcontrol GUI,

  click Abort
  click Reset
  click Download

• Start a new run.

List of HAPPEX crates

Running CODA for HAPPEX DAQ (up to date as of 9-23-09)

Note: This is for HAPPEX DAQ. If you want to run CODA for spectrometer DAQ see Running CODA for spectrometer DAQ.

• If switching from Spectrometer to HAPPEX DAQ, you must turn off detectors that can be damaged by high rate before turning on high current beam; for PVDIS this means the VDCs; use checklist when making this switch.

• Log in, if necessary, to adaql1 as user apar

• The Runcontrol GUI may be already running. If not, see section HAPPEX DAQ cold start. To start and stop runs, click on the buttons Start Run and End Run. Start Run is the same as the sequence Prestart, Go.

  Be sure to enable the online data monitor before starting the run, if you wish to use it during the run.

• Start a new run EVERY hour, even with no beam. Runs without beam are important for Electronics Crosstalk Analysis.

Switching CODA config between Happex and HapNoQweak (up to date as of 9-23-09)

HAPPEX/PVDIS Data Analysis

Online Data Monitor (up to date as of 9-23-09)

• HAPPEX online data monitor (PANGUIN) normally starts up at start of run. To disable this "background process" enter at a shell prompt:

  > panguin off

  To re-enable it enter:

  > panguin on

  These commands have no immediate effect on analysis, but govern whether or not analysis will start at the start of the next run.

• To monitor data online, log into adaql1 with the apar account and type at a shell prompt:

  > gopan
> online -f happex_lite
  

• or

> gopan
> pan
> online("panguin/happex_lite")


A fairly self-evident GUI will appear. Select various pages of plots using the buttons on the left.

NOTE: Please be warned that the GUI might crash for several reasons. Making it work again could simply be a matter of closing the window and restarting it. If at any point the GUI stops working and restarting does not work, then you you must do a HAPPEX DAQ cold start.

• Here is a list of what shift workers should look at when monitoring online:
  
  
  • There should be at least two BCMs in the 'BCMs 1-2 1D' tab with a healthy signal. A healthy signal can be characteized as being at or above 25,000 channels (except for BCM2, connected to an 18-bit ADC, which should be more than 150,000 channels).
    
  
  
  • There should be at least four BCMs in the 'BCMs 1u,1d, L&R' tab with a healthy signal. A healthy signal can be characteized as being correlated with the beam current <- update this for PVDIS!
    
    
  • In the 'BCM asymmetries' tab, the histograms shown should be centered at around zero and should agree with each other. Otherwise, Pockels Cell voltages might need to be adjusted so we can get them to zero.
    
  • In the 'BCM asymmetry correlations' tab, the histograms shown should be a nice skinny diagonal distribution near zero in both  axes. Otherwise, something is wrong with the BCM signals in the PVDIS crate. <- update this for PVDIS!
  • The BPM12 wires tab shows 4 plots. The mean on all these plots will normally be about 85000 channels and should be less than 130,000 channels. If these signals saturate, it would be a disaster for the experiment! For detailed instructions of what to do when these signals saturate, click here.
    .
  
  
  • The HAPPEX detectors shown in the 'HAPPEX Detector Signal and Correlations' tab should also have healthy signals. In this case, the signals should be:
    • More than   40,000 for det1
    • More than 150,000 for det2
    Some more detailed instructions can be found here. The Detector vs. BCM plots, located in the same tab, should show good correlation. <- remove this for PVDIS!
  • Do we have similar checks for PVDIS signals???
  • 
  
  
  • The Luminosity Monitors in the 'Blumi vs event number' tab should have healthy signals. Ideally, the signals should be at around 200,000 channels. If they are not, the HVs can be calibrated by connecting to the Right Arm HV crate and looking at slot 15. This should only be done after consulting with an expert, such as Rupesh Silwal, Luis Mercado or Dustin McNulty.<- update this for PVDIS?
  
  
  • Blumi vs BCM should show good correlation for all the signals.<- add bcm u1/d1 L&R for PVDIS?
  • The Total Pairs and Cuts tab should be examined during the run. This records how efficient our data taking is.<- does this stays unchanged for PVDIS?

Starting prompt analysis (up to date as of 9-23-09)

• The HAPPEX Prompt analysis is comparable to the Detector and Physics replay that is done with the Hall-A Analyzer.

  • Log into adaql5 or adaql6 with the apar account.
    DO NOT PERFORM PROMPT ANALYSIS ON ADAQL1
    
  • At the shell prompt, type:

    > gopan
> prompt runnumber

  • Prompt Analysis will then proceed with decoding the raw CODA data into Helicity Correlated Asymmetries and Position Differences, done by the Parity ANalyzer (PAN). This is followed by the Regression and Dithering Analysis (REDANA), which corrects the raw asymmetries for detector sensitivities to beam parameters.
  • The Online GUI will open a window presenting histograms and stripcharts for the requested runnumber. Check these versus the sample Prompt Analysis plots (should be in a white bound folder). Any strange deviations from the sample plots should be brought to someone's attention (Shift Leader, Run Coordinator) and shown in the HALOG. The reference plots (as of 9-23-09) are shown below:

  			changes to be made for PVDIS
  			Fig. 1 and 2 should have one of the PVDIS bcm copies. Fig. 3 should have (or another page should be added) for the asymmetry of PVDIS bcm copies, and their correlation with bcm1 or bcm2.
  			These 3 can stay the same
  			Fig. 7 and 8 should be replaced by PVDIS signals. Suggest rate and asymmetries of: e4n, e4w, e5n, e5w, pi4n, pi4w, pi5n, piw, and the overall en, ew, pin, piw, for both left and right arms.

  • If you start a prompt analysis before a run is finished, or for some reason you need to force the reanalysis of a run then use:

    > gopan
> reprompt runnumber

  • Once in a while, print out the text output files and put them in the binder (taking advantage of the opportunity to look them over and compare them to previous runs, of course). The print command is (after doing $ gopan) e.g.

    $ chaprint_text prompt_output/*_224*

    to print outputs from runs 2240 to 2249.

Spectrometer

Bringing up the Alarm Handler

• In the HAC control window, press the "Alarm Handler" label in the tools launcher. When an alarm is triggered, the bottom "Alarm Handler" will flash, then you can press there to see where the problem is.

Bringing up the HAC control window

• The machine to run HAC is hacsbc2, the second machine from left. At the bottom of the screen is the Linux taskbar. The sixth symbol is tools launcher. Pressing the arrowhead opens a menu which has:

  • Alarm Handler, bogies_LEFT, bogies_RIGHT, bogies_SetSpec, JavaArchiverClient,
  • Menu_Accelerator, Menu_ESR, Menu_HallA, snapshot, StripTool

  Pressing the "Menu_HallA" label launches a subscreen titled "Hall A Main Menu". One of the entries is labelled "Tools". Pressing on the "Tool" button opens the "Hall A General Tools" screen as follows, which is often referred to as the HAC window. The old version of HAC can be found at http://hallaweb.jlab.org/document/OPMAN/node179.html.

Changing momentum setting of HRS <- should get updates from the techs on this for PVDIS

• From the HAC control window, there is a P0 SET field for each spectrometer in which you can enter the desired momentum setting. To change to a lower momentum from a higher previous setting, you just need to enter the momentum value. To bring the momentum setting up, you need to recycle the magnets for Q2 and Q3 of either arm. That is increase the current of Q2/Q3 to 1600 A for the Left arm or 1400 for the Right arm, wait for 2 minutes after they reach max, then tune down the value to the desired setting. More detailed instructions are on the white board of the counting house. There's no need to recycle magnets for Q1 and Dipole.

• Procedure to reset the dipole momenta (eg. after a reboot of the magnet controls IOC):
  1. Look up (in the runsheets or the whiteboard) the desired SET current in the dipole magnet power supply.
  2. Turn OFF the field regulator in the dipole nmr field control gui.
  3. Set the desired momentum in the hall A tools screen (set the "P0").
  4. Enter the desired SET current in the dipole magnet power supply.
  5. Wait for the momentum setting of the dipole to reach within ~0.5% of the desired momentum.
  6. Turn ON the field regulator.
  7. Eventually, the regulator will automatically enter a new set current that will take the dipole directly to the desired momentum.
        Note:

     left dipole SET current ≁ (left dipole READ current)/(0.944)

     right dipole SET current ≁ (right dipole READ current)/(1.005)
     
  [This is a modified version of HAlog entry 129538].

Reset Q1 of Left or Right HRS <- should get updates from the techs on this for PVDIS

• From the HAC control window

• Go to Hall A tools screen and press the blue button next to "I(A)" for left or right HRS (depending on which one is having problems). Click on "Q1 power supply", this will pop up the window for power supply control.
• Usually after a trip, the Q1 current will drop to zero, some fault messages will show in red, and the power supply is off. Press the "Reset" button to clear the faults and wait, for an example see halog 152379. Note that "MAGNET MISMATCH" will remain on because the current readback does not match the set point.
• Try to turn on the power supply by clicking on "POWER ON". If it does not turn itself on, try the following:
• Go to the middle room, look for a "Reset switch box #1" in rack CH01B04, press the green button labeled "left Q1 local control reset" or "right Q1 local control reset";
• Go back to the control window and click on "POWER ON" again. If it still does not turn itself on, a controlled access is needed. In this case, consult the run coordinator first, and then go down to the hall.
  1. Go to Q1 power supply, put into local mode (a button).
  2. Press "reset", then "power on", then press local mode button again to go into remote (its a 2-state button). This might suffice. Ask shift crew to turn on magnet... see if it works.
  3. If this doesn't work, which happens all the time, then:
     • Go to the key panel on row of equipment behind Q1 PS (toward target), press yellow button under key switch.
     • And press tiny blue reset on back of this panel. There is a big sign pointing to this tiny button.
     • Repeat step 2.
• Now the power supply should be on. If it is not, you didn't do the above procedure correctly. In the control window, enter set current. If a set current is already there, check if it is the same as previous runs (check the runsheets). Wait for the magnet to ramp up.

Target

Checking target temperature

• The target temperature is displayed on the target GUIs, tgtcharts running on cryotarg as well as on the camera monitors on the shelves above the computers. Look at the camera monitor labeled "Control Rack", third top little monitor. It displays the temperatures for the three loops on three white temperature controllers, with loop 1 at the top and loop 3 on the bottom. Ask the TO for help if you can't find the temperature or it doesn't make sense.

New Procedure on target IOC reboot

• The green reset button in the counting house middle room should no longer be used. To reboot the IOC:
• Type "http://hareboot7" in a web browser and enter the username/passwd (they should be labeled next to the TO's computer);
• Select "Immediate Reboot" under "Control Action" for outlet 3 (iocha13);
• Click "Apply", wait for IOC to come back, and be patient;
• If the IOC stills behaves odd, consult the target on-call.
• In any case, do not press the green button!

Spectrometer Data Acquisition

Spectrometer DAQ cold start

Note: This is for spectrometer DAQ. If you want to cold start HAPPEX DAQ see HAPPEX DAQ cold start.

• The spectrometer DAQs runs on the a-onl account. Right HRS runs on adaql2 and the Left HRS runs on adaql3.

  Do the following at a shell prompt on adaql2 (adaql3) for the Right (Left) HRS DAQ on the a-onl account:

  > startcoda
  

• "startcoda" will run "kcoda", and will start all the components for you.

• Run Type = LeftHRS or RightHRS.

• Details about Hall A Spectrometer DAQ and trigger see Bob Michaels's guide.html and guide2.html.

Mapping of ROCs to Portserver and IP for Spectr. DAQ

        HRS-DAQ CODA Configrations 

        LeftHRS        Left spectrometer DAQ       on adaql3
        RightHRS       Right spectrometer DAQ      on adaql2

Triggers for HAPPEX <- update this for PVDIS!

We will sometimes run the spectrometer DAQ for optics, alignment check, Q² measurement, background studies, etc.

Here are the triggers on each HRS

• T1 = HAPPEX Detector = Electron calorimeter above a threshold.

• T2 = S0 detector = The "AND" of two PMTs.

• T3 - T7 various things for PVDIS.

• T8 = usually a 1024 Hz pulser

• Recall, T9 - T12 (if exist) cannot be prescaled

Rebooting HRS crates

• Short hint: Type "reboot" at vxWorks prompts of ROC logins.

• For details about Hall A spectrometer DAQ including reboot procedure see Bob Michaels' guide.html and guide2.html.

Running CODA on Spectrometer DAQ

Note: This is for spectrometer DAQ. If you want to run CODA for HAPPEX DAQ see Running CODA for HAPPEX DAQ.

• Important: Use the checklist when switching between spectrometer and HAPPEX DAQ.

• Log in, if necessary, to adaql2 (adaql3) for Right (Left) HRS as user a-onl

• The Runcontrol GUI may be already running. If not, see section Spectrometer DAQ cold start. To start and stop runs, click on the buttons Start Run and End Run. Start Run is the same as the sequence Prestart, Go.

• For more details about Hall A DAQ and trigger see Bob Michaels's guide.html and guide2.html.

Starting xscaler (HRS) and checking trigger rate <- update this for PVDIS!

• Use hapc5 which is the PC on the top at the far right of counting room console. Normally xscaler will be running, but if not, log on as adaq, type "xscaler" and do what is commanded of you.

• To start xscaler (though usually it is already running):

  xscaler

• You can find all trigger rates in Normalization page.

Spectrometer Data Analysis

Analysis for Spectrometer DAQ data

We will do frequent spectrometer-DAQ runs for the following purposes:

• Optics Calibration (not so frequent) at low current.
• Q² Distribution measurement at low current.
• PVDIS deadtime study, including rate/current scan; tagger must be on for this kind of runs.
• PVDIS PID study (at least once a day), could be low current.
• Test XYQ cavity BPM to 10 nA (will we do this for PVDIS?).
• Background Analysis from Aluminum End Caps, same current as LD2.
• Background analysis using field scan to simulate trajectories from inelastics and from pole-tip scattering.

Important: Use the checklist when switching between spectrometer and HAPPEX DAQs.

Instructions for online checks: <- Update this for PVDIS!

• There are, at the moment, competing analysis codes. (Not a bad thing.) This section explains the one Bob has been maintaining. Ask Dustin or Ramesh for theirs.
• Login to adaq account and type goonlana This should take you to ~adaq/happexsp/onlana. The "sp" means spectrometer DAQ.
• Type bobana and use the script .x onlana.C.
There may be other versions of this, look for notes in the counting room.
• The script will tell you what to do next. Typically you must run online GUI configurations to check data quality. Examples:

  • .x online.C+("detectorL")   L-HRS detector checkout (detectorR for R-HRS)

  • .x online.C+("opticsL")   optics data taking check

  •         .x PID???
  •         .x tagger/deadtime???

  • (etc ...)

• For further details see the README file in the workding directory.

Hall A Detectors

List of Detectors (up to date as of 10-28-09)

• Standard Detectors used for production running during PVDIS:
• S1 and S2 scintillators;
• Gas cherenkovs (with the extension box on both arms);
• lead glass counters: pion rejection on the LHRS and preshower/shower on the RHRS;

• HAPPEX Specific Detectors
  • A whole host of beamline instrumentation too numerous to mention here.

• Standard Detectors used for systematic studies (such as optics or Q2 measurements).
  • VDCs (the HV must be turned off during high rate running)

Detector High Voltages (up to date as of 9-23-09)

Left arm High Voltage screens are located within the Hall-A Main Menu screen, under Lecroy HV


Beamline(Compton):


Detector	Mainframe ID/Slot #	Card #	Channel #	HV (V)
Compton GSO	2	11	1	-1800
Compton Finger	2	11	7	-2000
Compton Finger	2	11	8	-1000

The screen should look like this:



Left Arm (HAPPEX det/S0): <- Update or remove this for PVDIS!


Detector	Mainframe ID/Slot #	Card #	Channel #	HV (V)
S0 - Front End	7	2	1	-1700
S0 - Back End	7	2	7	-1700
HAPPEX Det	7	2	9	-1590 (Integrate Mode)
HAPPEX Det	7	2	9	-1900 (Counting Mode)

The screen should look like this:


Right Arm Bottom:
Right Arm HV are no longer available through the Hall A Tools gui. The VNC hvgui must be used to access that HV crate. See below:

VNC HV server (R-HRS detectors)

• Starting HVgui for Right HRS detector HV
  • login as adev@adaql5 (passwd on wall)
  • type "start_hvgui" If the command fails with message that a server is already running, this may be ok. It may only mean that the server has already been launched. Or it could mean that someone is running the vt100 interface. Try the next step.
  • If the gui interface does not open, type "hvgui"

The screen should look like this:

Right Arm (HAPPEX det/S0):<- Update or remove this for PVDIS!

VDC check and high voltage

• VDC Status

  • VDC status can be checked on the HAC control window (see below). High Voltages and Gas Flows are constantly being monitored.

• VDC HV (IMPORTANT: HV must be turned off during high rate running, i.e. HAPPEX production running.)

  • Bring up the HAC control window (see below)

  • In the "VDC HV" section, set HV to 0

  • In the "Miscellaneous" section, click on the Crate Resets button.

  • In the "Hall A Slow Controls" window, press the "Reset" button associated with the tripped HV crate.

  • Go back to set HV values to 4.0 kV

Helicity Controls

Changing the Half Wave Plate (up to date as of 9-23-09)

1. Inform Hall B that we are about to change the half-wave plate. If they are in the middle of the run, then ask them to inform you when their run ends. Once we get the green light from Hall B, proceed into the following steps.
2. End the current HAPPEX run and the current Compton Run.
3. Call MCC and ask them to change the state of the Insertable Half-Wave Plate (IHWP) from In to Out or Out to In as appropriate.
4. When you see the state of the IHWP change in the HAPPEX feedback monitor, type in an xterm (logged in as apar, make sure to log in with the argument -Y):
        flipper
5. The new setpoints should now appear in the HAPPEX feedback monitor.. ingeneral the Rotatable Half-wave Plate (RHWP) takes a minute or two to change, but HAPPEX III uses the same RHWP position for both HWP states.
      DO NOT START A NEW RUN UNTIL YOU HAVE VERIFIED THE NEW SETPOINTS.



6. Start a new HAPPEX run and a new Compton Run.
7. Make a halog entry, saying you've changed the IHWP, and include a screen capture of the HAPPEX feedback monitor (the "runbird" GUI).
8. Write the new half-wave plate configuration on the white board.

Below is a sample of what the output looks like (from flipper).

[apar@adaql6 ~]$ flipper
 
****************************************
 
 Only run this program when the IHWP change has
 already been made.  If not, please Ctrl-C out now!
 
 Current slugnumber = 4
 Increment slugnumber? (Y/N)
Y
New slugnumber = 5
 
Current IHWP = OTU
Desired Settings for IHWP = OUT
     Hall-A IA = 4.79
     Hall-C IA = 5.00
     PC Pos    = 8.100
     PC Neg    = 6.610
     RHWP      = 1200
Current settings (to be changed)
     Hall-A IA = 4.79
     Hall-C IA = 5.0
     PC Pos    = 8.575
     PC Neg    = 6.125
     RHWP      = 1200
Writing the current seetings to file /adaqfs/halla/apar/feedback/IHWP.IN for the next flip back.
Performing Flip to IHWP = OUT settings
Halfwave plate OUT, Slug 5
 
Done... Please verify the new setpoints in the HAPPEX Feedback Monitor.
 

PITA Scan (up to date as of 9-23-09)

1. End the current HAPPEX run and the current Compton Run.
2. Check the status of the IHWP (IN or OUT), and set it to the state desired.
3. Turn off the HAPPEX feedback monitor by typing
        feedback off
   in an xterm (logged in as apar). You should check that the feedback status is indeed off on runbird.
4. Set the PC voltages appropriate for the IHWP setting. To set the voltages, open Hall Parity Controls from the Gun/Laser in the Accelerator Main Menu. We are using GUN2 currently. The voltages should be set for GUN2: PC (PITA) POS and GUN2: PC (PITA) NEG appropriately. Check the run-sheet from the previous runs to make sure the voltage you have is correct for the current IHWP setting.
   If for some reason, you are not able to change the voltages on the Hall Parity Controls , call MCC and ask them to do so!
   



5. Start greenmonster from apar@adaql1 by typing greenmonster.
6. Go to the ScanUtil tab, and click on NOT CLEAN. Set the values on Set Point 1 and Set Point 2 to 0 . Click on Set Values, and check that the set points are indeed set to 0 by clicking on Check Status .
7. Start a new HAPPEX run.
8. After about 200 events click on CLEAN .
9. After about 10000 GOOD events (beam trip events are not GOOD events), click on NOT CLEAN .
10. Set the PC (PITA) POS to the previous value + 1 and PC (PITA) NEG to the previous value -1 . For instance, if the previous POS/NEG were 8.5/6.2 , the new values should be 9.5/5.2 .
11. Set the values on Set Point 1 to +60 . Click on Set Values, and check that it is set to +60 by clicking on Check Status .
12. Click on CLEAN .
13. Repeat steps 9-12 , but setting the voltages in the opposite direction. The new set points should be POS/NEG 7.5/7.2 , and Set Point 1 at -60 for the example above.
14. After about 10000 GOOD events , end the HAPPEX run, and run the prompt analysis in apar@adaql4 by doing gopan, prompt runnumber .
15. After the prompt replay is done, run hapPITA.C gui by typing gopan, pan, then
    .x lmacro/hapPITA.C(runnumber)
16. Make a halog entry with the PITA slope, IHWP status, run # and the output plot of the gui with the PITA slope. Here is a typical PITA plot.



17. Write the half-wave plate configuration on the white board.

HAPPEX Charge Asymmetry Feedback (up to date as of 9-23-09)

1. The only thing that needs to be changed after each PITA/IA scan is the feedback slope, which is done in the file panFFB.db in ~/feedback/ in apar account.
2. To turn charge feedback on, type feedback on
3. To turn charge feedback off, type feedback off
4. The charge feedback status should be checked in rundirb , which can be brought up by typing rundird .

Miscellaneous

Bringing up the Beamtime Counting Table

• Log in to adaql1 as user adaq

• Type "bta"

• An attempt is made to automate the entries, but the shift leader should check it based on their own estimates of ABU, BANU, etc.

Plotting time dependences of EPICS variables

• In the HAC control window, press the "StripTool" label in tools launcher, which allows you to plot any EPICS variables versus time.

Printing in the counting house

• On hopefully all adaq computers the command print should work. Type print filename for a file named filename and it will print out on the cha2hp printer in the back room. If you want to print to another printer, type print filename otherprinter. If that doesn't work try the command line below.

  rlpr -Pcha2hp -Hjlabprt file.ps

  Printing from Mozilla:

  • Use

    File->Print...

  • Choose to print to printer, not file

  • Click on Properties (or Configuration?) of printer

  • In the field for Print command, enter:

    /apps/bin/rlpr -Pcha2hp -Hjlabprt

    (you should only have to do this once for each account)

  • Click Print

  Alternatively, you can have Mozilla print to a Postscript file, which you can then print from the command line.

  Trying to print to cha2hp from a CUE machine (e.g. jlabl1) using pdq will also fail. This is not a problem specific to the counting house computers. Only lpr and rlpr will work with this printer.

Starting HALOG (up to date as of 9-23-09)

• As user adaq on any adaq.. machine, simply type

  > halog

• Entering text is easy and straightforward. After submitting the entry, the white text on blue background in the lower right corner of the window should read 'Entry complete', otherwise something is wrong.

• Entering graphics: Click Grab Screen in the bottom button row of the halog window. The halog window will disappear, and the window the cursor is in will become the active window, its outline flashing. You can select any window by clicking in it on the left mouse button. You also can select an arbitrary part of the screen by holding down the left mouse button and dragging the cursor along. All the time a rectangle will flash that indicates the selected area. Releasing the mouse button will then cause this screen area to be included into the entry. It will show up as a thumbnail picture in the halog window, where you can discard it or accept it, or go for a second screen grab. The images are in GIF format.

• For more details about HALOG see halog HOWTO and FAQ page.

Starting spot++ and checking the raster

• Log in to as adaq on adaql4 or any other adaq Linux computer.

• Make sure CODA is running with beam on. Of course, that's the spectrometer DAQ, not the HAPPEX DAQ. You'll need some triggers (adjust prescale factors to get at least 50 Hz of something, if possible).

• Type spot++ from any directory, after about 30 seconds, plots will pop up.

• Hint: Type "spot help" to learn more options.

Other Problems

If you can't solve a problem

• Call Run Coordinator A.S.A.P.
  Cell phone: 876-1787. Generic pager: 584-5411, but the RC might have his own pager, see white board.
• Techs:  See the white board. They normally want to be paged before phoned at home. Always contact the Tech-on-call first; never call any other Tech without permission from Tech-on-call.
• Computers:   Page Ole Hansen (7627) or Bob Michaels (7410).
• HAPPEX DAQ:  Page Bob Michaels (7410) or Luis Mercado (0042).
• Spectrometer DAQ:   Page Bob Michaels (7410) or Bodo Reitz (5064).

HAPPEX Home

webmaster Last modified: 10/28/2009who