Run Plan for Tonight and Tomorrow

keyword=Run Plan for Tonight and Tomorrow

Run Plan

The plan for the night: Take production data! Watch the lumi widths to see if anything changes. Please check the histograms on the online data monitor with the reference ones on the shift how-to page (http://hallaweb.jlab.org/experiment/HAPPEX/opmanual/opmanual.html#HPXStartingonlineanalysis).

Take Compton data! You will need to start a new Compton run every two hours. The CODA screen to start and stop the Compton runs is in the back room. The optimal background rate seems to be 100 Hz/muA, but if it over 300 Hz/muA, call MCC and have them adjust the beam tune.

If the background rates get too high, the Compton HV will trip off and you won't be able to take data. If you cannot keep it going, call Megan Friend (412-302-0576, which is an out-of-state cell phone, so you cannot call from the counting house without a long-distance code; she'll replace the batteries in her pager soon, which will be 584-0038), and if you cannot get her, page Alexandre Camsonne (584-5064).
Keep an eye on the Compton strip chart (in the front room computer on the Compton desktop on the computer with the magnet and HV controls). If the blue compton:RATE_G parameter flatlines, something has crashed and a coda reboot needs to be done. Also keep an eye on the ROCs. These can be found on the Compton computer (in the corner in the back room) on the rocs desktop. If hitting enter in a ROC window does not give you an arrow, a ROC has crashed and you need to do a coda reboot.

Run spot++ every couple of hours and log it. Change the prescale factor PS8 to 1 and PS1 and 2 to 99999 for this.

Change the half-wave plate state when we get to 1M good pairs. Follow the instructions for doing this and running the flipper script here: http://hallaweb.jlab.org/experiment/HAPPEX/opmanual/opmanual.html#ChangingHalfWavePlate. Please note that there are updated instructions for using flipper (including logging in as apar using -Y).

Bob Michaels will come in to do the second part of his Compton DAQ tests tonight at 11:00pm (it will run until 3:00am). This will not affect the production running.

If you lose beam for an extended period, do our beam diagnostics to make sure that everything is good (the optimal values for the raster, beam position, beam current, lumi RMS, and detector asymmetry RMS are on the whiteboard).

With an empty target, do harp scans, which are done by MCC on request.
Still with an empty target, do spot++ at 40 muA. Change the prescale factor PS8 to 1 and PS1 and 2 to 99999 to do spot++.
Make sure that the raster is on!! Check that it is at the correct size.
After ensuring that the raster is on, put in the hydrogen target and start taking production data.

We are really behind in our data goals at this point. Please do not be shy about calling in the expert on something if it is holding things up.

At about 10:00am tomorrow, Rupesh will come in to do a second position scan. I will post instructions for this in a later post.

After the position scan, if Alexandre wants to make his access, he'll do it then.

Swing shift tomorrow: Dustin is tentatively planning on a Q^2 measurement, depending on how his data analysis tonight goes.

Scot Spiegel would like to make an access if we are going to be down for a while at a time when we can go to controlled access (in the daytime, 8am-5pm) to get some poly for shielding. If such a time presents itself, his extension is x5900, his cell is 757-536-5900, and his pager is 757-584-5900.
Page Heidi if there is an access in the daytime (6915).
If anyone must reset a magnet, they must make a halog entry stating which magnet on which arm, and what was wrong with it to require a reset. The word "tech" must appear in the subject line.
Be sure that the prompt analysis is done for every run!
Please log CODA reboots in the halog and shift summary so that it is easier to track how much time is lost to these reboots.
The BTA program doesn't subtract any time to speak of for beam trips. Please manually subtract a full minute for each beam trip in the beam time accounting.
Please write a detailed shift summary (including runs taken and any activities) and submit the BTA for each shift.
Please make sure that the shift checklist is done once each shift.
If you have to page or call someone for support, please do so from a counting house phone or it will be ignored!
Keep a close eye on the lumi widths (RMS) as we take data.
Please continue to take runs even if there is no beam. These data can be used to determine pedestals. Please label these runs as having no beam.
The PVDIS people would like their scintillators on. See halog entry 290362.