NEXT
Make New Entry,
Make Followup Entry
User name apar
Log entry time 07:51:31 on November 16, 2009
Entry number 300301
keyword=End_of_Parity_Run_13996__CODA_Config=Pvdis
************************************************
Run Number: 13996
End of Run Comment:
Run_type=Production,beam_energy=6.08,beam_polarization=87,beam_raster=on,comment_text=production, 70 muA,dithering_magnet=on,dithering_magnets=,leftarm_p=3.66,leftarm_theta=12.9,parity_feedback=on,parity_ihwp=out,rightarm_p=2.63,rightarm_theta=20,target_fanspeed=60 Hz,target_type=20cm LD2
************************************************
End-of-Parity-run EPICS data for Run Number 13996 at Mon Nov 16 07:49:06 EST 2009
CODA Configuration: Pvdis
Laser power :
Compton Run Number : compton:RUN --- Invalid channel name
-----------------------------------------
Wien angle : 74.7279
Wien BDL : 1728.2
Wien field : 49.796
Laser attenuation Hall A : 134
Laser power Hall A : 100
Beam Half-wave plate Set(off=out) : IN
Beam Half-wave plate Read(off=out) : IN
Rotating waveplate : 1200
IA Cell Setpoint Hall A : 4.79
IA Cell Setpoint Hall C : 4.87
PZT X Setpoint Hall A : 5.25
PZT Y Setpoint Hall A : 5
PZT X Setpoint Common : 5.1
PZT Y Setpoint Common : 5
Gun2: PC (PITA) POS : 8.183
Gun2: PC (PITA) NEG : 6.517
Gun3: PC (PITA) POS : 5.0246
Gun3: PC (PITA) NEG : 5
Pockels Cell Voltage POS : 1.75336
Pockels Cell Voltage NEG : 1.54579
Helicity Clock Set : Free Clock
Helicity Delay Set : 8 cycles
Helicity Pattern Set : Quartet
Helicity Clock Read : Free Clock
Helicity Settle Read : 500
Helicity Delay Read : 8 cycles
Helicity Pattern Read : Quartet
Helicity Frequency : 29.5596
-----------------------------------------
Compton stuffs
-----------------------------------------
Calculated power in cavity : COMPTON_PW1PCAV_ca --- Invalid channel name
Laser power : COMPTON_LASERP_si --- Invalid channel name
Photodiode on table : COMPTON_PW2PCAV_ca --- Invalid channel name
Calculated power in cavity : COMPTON_PW1PCAV_ca --- Invalid channel name
Laser X position on QPD 1 : COMPTON_Y1SS_ca --- Invalid channel name
Photodiode on table : COMPTON_PW2PCAV_ca --- Invalid channel name
Laser Y position on QPD 1 : COMPTON_X1SS_ca --- Invalid channel name
Laser X position on QPD 1 : COMPTON_Y1SS_ca --- Invalid channel name
Laser X position on QPD 2 : COMPTON_Y2SS_ca --- Invalid channel name
Laser Y position on QPD 1 : COMPTON_X1SS_ca --- Invalid channel name
Laser Y position on QPD 2 : COMPTON_X2SS_ca --- Invalid channel name
Laser X position on QPD 2 : COMPTON_Y2SS_ca --- Invalid channel name
QPD 1 sum : COMPTON_XYSUM1_ca --- Invalid channel name
Laser Y position on QPD 2 : COMPTON_X2SS_ca --- Invalid channel name
QPD 2 sum : COMPTON_XYSUM2_ca --- Invalid channel name
Position set point for adjustable
QPD 1 sum : COMPTON_XYSUM1_ca --- Invalid channel name
mirror 1 (either x or y) : COMPTON_POS1_si --- Invalid channel name
Position set point for adjustable
QPD 2 sum : COMPTON_XYSUM2_ca --- Invalid channel name
Position set point for adjustable
mirror 2 (either x or y) : COMPTON_POS3_si --- Invalid channel name
mirror 1 (either x or y) : COMPTON_POS1_si --- Invalid channel name
Position set point for adjustable
Laser minimum temperature (35.8) : COMPTON_LASERT_MIN --- Invalid channel name
mirror 2 (either x or y) : COMPTON_POS3_si --- Invalid channel name
Laser temperature set point : COMPTON_LASERT_si --- Invalid channel name
Laser minimum temperature (35.8) : COMPTON_LASERT_MIN --- Invalid channel name
Polarisation in cavity : COMPTON_SU_POLAR_mo --- Invalid channel name
Laser temperature set point : COMPTON_LASERT_si --- Invalid channel name
Reflection photodiode : COMPTON_SERVO_PDRai --- Invalid channel name
Polarisation in cavity : COMPTON_SU_POLAR_mo --- Invalid channel name
Gain of locking servo : COMPTON_SERVO_GAINao --- Invalid channel name
Reflection photodiode : COMPTON_SERVO_PDRai --- Invalid channel name
Tracking level (V) of locking servo : COMPTON_SERVO_SEUILao --- Invalid channel name
Gain of locking servo : COMPTON_SERVO_GAINao --- Invalid channel name
Slow locking signal sent to laser : COMPTON_SERVO_SLOWai --- Invalid channel name
Tracking level (V) of locking servo : COMPTON_SERVO_SEUILao --- Invalid channel name
Fast locking signal sent to laser : COMPTON_SERVO_FASTai --- Invalid channel name
Slow locking signal sent to laser : COMPTON_SERVO_SLOWai --- Invalid channel name
Calculated polarisation in cavity : COMPTON_CAVPOLAR_ca --- Invalid channel name
Fast locking signal sent to laser : COMPTON_SERVO_FASTai --- Invalid channel name
Photodiode 1 after Wollaston prism : COMPTON_PW1R_S1_ca --- Invalid channel name
Calculated polarisation in cavity : COMPTON_CAVPOLAR_ca --- Invalid channel name
Photodiode 2 after Wollaston prism : COMPTON_PW1R_S2_ca --- Invalid channel name
Photodiode 1 after Wollaston prism : COMPTON_PW1R_S1_ca --- Invalid channel name
Step size for RHWP scan : COMPTON_PVAL_Y_ao --- Invalid channel name
Photodiode 2 after Wollaston prism : COMPTON_PW1R_S2_ca --- Invalid channel name
Laser temp slow ramp (1 = on) : COMPTON_CAVSLOW_bo --- Invalid channel name
Step size for RHWP scan : COMPTON_PVAL_Y_ao --- Invalid channel name
Extent of laser temp slow ramp (C) : COMPTON_LASERT_RAMPDT --- Invalid channel name
Laser temp slow ramp (1 = on) : COMPTON_CAVSLOW_bo --- Invalid channel name
Speed of laser temp slow ramp up : COMPTON_CAVPLUSOFT_ca.B --- Invalid channel name
Extent of laser temp slow ramp (C) : COMPTON_LASERT_RAMPDT --- Invalid channel name
Speed of laser temp slow ramp down : COMPTON_CAVMOINSOFT_ca.B --- Invalid channel name
-----------------------------------------
Left Arm Magnets
-----------------------------------------
Left Arm Q1 power supply current : 2753.7
Left Arm Q1 momentum : 3.66015
Left Arm Q1 gauss meter : -0.23203
Left Arm Q1 power supply polarity : 1
Left Arm Q2 power supply current : 1575.52
Left Arm Q2 momentum : 3.65891
Left Arm Q2 gauss meter : 0.8271
Left Arm Q2 power supply polarity : disabled
Left Arm D1 power supply current : 1325.27
Left Arm D1 momentum : 3.66009
Left Arm D1 NMR : 1.35578
Left Arm Q3 power supply current : 1456.78
Left Arm Q3 momentum : 3.65916
Left Arm Q3 gauss meter : -0.73421
Left Arm Q3 power supply polarity : disabled
-----------------------------------------
Right Arm Magnets
-----------------------------------------
Right Arm Q1 power supply current : 1977.7
Right Arm Q1 momentum : 2.63015
Right Arm Q1 gauss meter : -0.04918
Right Arm Q1 power supply polarity : 1
Right Arm Q2 power supply current : 1131.71
Right Arm Q2 momentum : 2.62964
Right Arm Q2 gauss meter : 0.5919
Right Arm Q2 power supply polarity : enabled
Right Arm D1 power supply current : 932.005
Right Arm D1 momentum : 2.63002
Right Arm D1 NMR : 0.975968
Right Arm Q3 power supply current : 1046.38
Right Arm Q3 momentum : 2.62969
Right Arm Q3 gauss meter : 0.4682
Right Arm Q3 power supply polarity : disabled
-----------------------------------------
HallA & Injector BCMs and Energy
-----------------------------------------
Average current of the two cavities : 69.165
Current on Unser monitor : 86.9867
Current on Upstream bcm : 67.4971
Current on Downstream bcm : 70.8328
Upstream Cavity Coefficient : 42.6
Downstream Cavity Coefficient : 43.8
Current on IBC0L02 (source) : 69.5134
Tiefenbach Hall A energy : 6067.4
Tiefenbach Hall C energy : 6070.48
Delta(E)/E width (MV_AI_DXWID) : 0.653842
MBSY1c Hall A Beam energy : 6081.48
MBSY3c Hall C Beam energy : 6090.49
MBSY1c magnet current (amp) : 254.343
MBSY1c Bdl : 1.51764e+06
-----------------------------------------
ARC stuff and Raster
-----------------------------------------
Arc1 dp/p : 0
Arc2 dp/p : 0
Raster X width : 6
Raster Y width : 6
-----------------------------------------
Target BPMs
-----------------------------------------
IPM1C12.XPOS : 0.0140426
IPM1C12.YPOS : 0.17478
IPM1H04A.XPOS : -0.712364
IPM1H04A.YPOS : 0.00231999
IPM1H04B.XPOS : -0.694566
IPM1H04B.YPOS : -0.000420451
Survey X offset bpm4A : -0.63
Survey Y offset bpm4A : -0.9
Survey X offset bpm4B : 0.77
Survey Y offset bpm4B : -1
Survey X offset bpm12 : 0.0140426
Survey Y offset bpm12 : 0.17478
Survey X HI SAT bpm12 : 0
Survey Y HI SAT bpm12 : 0
-----------------------------------------
CRYO TARGET INFO
-----------------------------------------
Target : L1 20cm
Encoder position : 33077688
fan frequency loop 1 : 59.5
fan frequency loop 2 : 0
fan frequency loop 3 : 0
temperature loop 1-1 : 22.32
temperature loop 1-2 : 21.99
temperature loop 1-3 : 22.5
temperature loop 2-1 : 100.09
temperature loop 2-2 : 95.14
temperature loop 2-3 : 119.99
temperature loop 3-1 : 99.99
temperature loop 3-2 : 99.99
temperature loop 3-3 : 29.99
pressure fill target H2 : 25.2934
pressure fill bottle H2 : 25.4292
pressure ballast H2 : 25.1499
pressure exhaust H2 : 25.3529
cryogen input temp : 218.3
crogen return flow : 0
JT valve setting : -0.341797
-----------------------------------------
Parameters used for HAPPEX feedback
-----------------------------------------
Parity DAQ Feedback Control (ON=1) : 1
HAPPEX Feedback results from
/adaqfs/halla/apar/feedback/runlog/ffb_13996.log:
Cumulative stats for 100104 events:
Events failing cut conditions:
0 Low_beam 8931
1 Beam_burp 143
2 Evt_seq 0
3 Pair_seq 926
4 Startup 1
5 Low_beam_c 0
--------------------------------------------------
epicsRunEnd ... for run 13996
Speed of laser temp slow ramp up : COMPTON_CAVPLUSOFT_ca.B --- Invalid channel name
Speed of laser temp slow ramp down : COMPTON_CAVMOINSOFT_ca.B --- Invalid channel name
-----------------------------------------
Left Arm Magnets
-----------------------------------------
Left Arm Q1 power supply current : 2753.64
Left Arm Q1 momentum : 3.66015
Left Arm Q1 gauss meter : -0.23203
Left Arm Q1 power supply polarity : 1
Left Arm Q2 power supply current : 1575.52
Left Arm Q2 momentum : 3.65891
Left Arm Q2 gauss meter : 0.8271
Left Arm Q2 power supply polarity : disabled
Left Arm D1 power supply current : 1325.27
Left Arm D1 momentum : 3.66009
Left Arm D1 NMR : 1.35578
Left Arm Q3 power supply current : 1456.78
Left Arm Q3 momentum : 3.65916
Left Arm Q3 gauss meter : -0.73421
Left Arm Q3 power supply polarity : disabled
-----------------------------------------
Right Arm Magnets
-----------------------------------------
Right Arm Q1 power supply current : 1977.7
Right Arm Q1 momentum : 2.63015
Right Arm Q1 gauss meter : -0.04916
Right Arm Q1 power supply polarity : 1
Right Arm Q2 power supply current : 1131.71
Right Arm Q2 momentum : 2.62964
Right Arm Q2 gauss meter : 0.5919
Right Arm Q2 power supply polarity : enabled
Right Arm D1 power supply current : 932.005
Right Arm D1 momentum : 2.63002
Right Arm D1 NMR : 0.975968
Right Arm Q3 power supply current : 1046.38
Right Arm Q3 momentum : 2.62969
Right Arm Q3 gauss meter : 0.4681
Right Arm Q3 power supply polarity : disabled
-----------------------------------------
HallA & Injector BCMs and Energy
-----------------------------------------
Average current of the two cavities : 68.8546
Current on Unser monitor : 88.0397
Current on Upstream bcm : 67.2651
Current on Downstream bcm : 70.4441
Upstream Cavity Coefficient : 42.6
Downstream Cavity Coefficient : 43.8
Current on IBC0L02 (source) : 68.892
Tiefenbach Hall A energy : 6067.35
Tiefenbach Hall C energy : 6070.48
Delta(E)/E width (MV_AI_DXWID) : 0.81189
MBSY1c Hall A Beam energy : 6081.48
MBSY3c Hall C Beam energy : 6090.49
MBSY1c magnet current (amp) : 254.343
MBSY1c Bdl : 1.51764e+06
-----------------------------------------
ARC stuff and Raster
-----------------------------------------
Arc1 dp/p : 0
Arc2 dp/p : 0
Raster X width : 6
Raster Y width : 6
-----------------------------------------
Target BPMs
-----------------------------------------
IPM1C12.XPOS : 0.00584361
IPM1C12.YPOS : 0.177356
IPM1H04A.XPOS : -0.711929
IPM1H04A.YPOS : -0.0217808
IPM1H04B.XPOS : -0.700411
IPM1H04B.YPOS : -0.023622
Survey X offset bpm4A : -0.63
Survey Y offset bpm4A : -0.9
Survey X offset bpm4B : 0.77
Survey Y offset bpm4B : -1
Survey X offset bpm12 : 0.00212345
Survey Y offset bpm12 : 0.191502
Survey X HI SAT bpm12 : 0
Survey Y HI SAT bpm12 : 0
-----------------------------------------
CRYO TARGET INFO
-----------------------------------------
Target : L1 20cm
Encoder position : 33077688
fan frequency loop 1 : 59.5
fan frequency loop 2 : 0
fan frequency loop 3 : 0
temperature loop 1-1 : 22.29
temperature loop 1-2 : 22
temperature loop 1-3 : 22.51
temperature loop 2-1 : 100.09
temperature loop 2-2 : 95.14
temperature loop 2-3 : 119.99
temperature loop 3-1 : 99.99
temperature loop 3-2 : 99.99
temperature loop 3-3 : 29.99
pressure fill target H2 : 25.2399
pressure fill bottle H2 : 25.4551
pressure ballast H2 : 25.2033
pressure exhaust H2 : 25.4276
cryogen input temp : 218.3
crogen return flow : 0.477187
JT valve setting : -0.78125
-----------------------------------------
Parameters used for HAPPEX feedback
-----------------------------------------
Parity DAQ Feedback Control (ON=1) : 1
HAPPEX Feedback results from
/adaqfs/halla/apar/feedback/runlog/ffb_13996.log:
Cumulative stats for 100104 events:
Events failing cut conditions:
0 Low_beam 8931
1 Beam_burp 143
2 Evt_seq 0
3 Pair_seq 926
4 Startup 1
5 Low_beam_c 0
--------------------------------------------------