Information on the Hall A IOCs

Input/Output Controller (IOC) Info for Hall A

iocBPMTC ( 129.57.242.18 )
- no serial available to Hall A
- no reboot available to Hall A
- located in rack 1H75B10
iocha1 ( 129.57.242.10 ) - beamline wire scanners (Accelerator)
- no serial available to Hall A
- no reboot available to Hall A - on hareboot
- located in rack 1H75B06
iocha2 ( 129.57.242.102 ) - 9th Dipole ioc
- no serial available to Hall A
- no reboot available to Hall A - on mapreboot ( 129.57.243.16 )
iocha3 ( 129.57.242.103 ) - RICH Detector Slow Controls ( presently not installed )
- serial port on "telnet hatsv40 2004" or "telnet 129.57.243.201 2004"
- "soft" reboot(backplane reset) on General Tools - Crate Resets - Resets from the Hadron Detector Stack (left) Crate - RICH Detector
- "hard" reboot(AC power cycle) on hareboot2 outlet 1 ( will reboot iocha3 AND iocha4 )
- located on the second level electronics platform on the Left Detector Stack, iocha3 and iocha4 share the same VME crate
iocha4 ( 129.57.242.104 ) - Left Arm Detector Stack Slow Controls
- serial port on "telnet hatsv40 2003" or "telnet 129.57.243.201 2003"
- "soft" reboot(backplane reset) on General Tools - Crate Resets - Resets from the Beamline Crate - Left Arm Detectors' Slow Controls VME Reset
- "hard" reboot(AC power cycle) on hareboot2 outlet 1 ( will reboot iocha3 AND iocha4 )
- located on the second level electronics platform on the Left Detector Stack, iocha3 and iocha4 share the same VME crate
iocha5 ( 129.57.242.105 ) - BCM (located in CRA)
- "soft" reboot(backplane reset) by walking into the center room of the Counting Room and pressing reset button on the IOC itself
- "hard" reboot(AC power cycle) on hareboot5 outlet 1
iocha11 ( 129.57.242.111 ) - Right Arm Detector Stack Slow Controls
- serial port on "telnet 129.57.243.204 2005" or "telnet portservhawt1 2005"
- "soft" reboot(backplane reset) on General Tools - Crate Resets - Resets from the Beamline Crate - Right Arm Detectors' Slow Controls VME Reset
- "hard" reboot(AC power cycle) on hareboot22 outlet 3 ( will reboot iocha11 AND whatever is on the other backplane )
- located on the first level electronics platform on the Right Detector Stack, in a split backplane VME crate
iocha12 ( 129.57.242.112 ) - Beamline slow controls
- serial port on "telnet 129.57.243.205 2002" or "telnet hatsv42 2002"
- "soft" reboot(backplane reset) - Green button 8 in Reset Box #2 in middle room of Counting Room, in rack CH01B04
- the IOC, iocha12, is located in the bottom of rack 1H75B09 in the beamline racks
iocha13 ( 129.57.242.113 ) - Cryo Target
- serial port on "telnet 129.57.243.203 2004" or "telnet portservha48 2004"
- "hard" reboot(AC power cycle) on hareboot7 outlets 5 and 6 (hot swap power supplies)
iocha14 ( 129.57.242.114 ) - Left Arm Gantry (Q2,D,Q3) Slow Controls
- serial port on "telnet 129.57.243.202 2002" or "telnet portservha16 2002"
- "hard" reboot(AC power cycle) on hareboot10 outlet 1
- located in the Left Shield House under the Boxbeam
iocha16 ( 129.57.242.116 ) - Right Arm Gantry (Q2,D,Q3) Slow Controls
- serial port on "telnet 129.57.243.204 2002" or "telnet portservhawt1 2002"
- "hard" reboot(AC power cycle) on hareboot25 outlet 7
- located in the Right Shield House under the Boxbeam
iocha17 ( 129.57.242.117 ) - Gas Shed Slow Controls
- serial port on "telnet 129.57.243.200 2002" or "telnet hatsv14 2002"
- "soft" reboot(backplane reset) by walking out to Gas Shed and pressing reset button on the IOC itself
- "hard" reboot(AC power cycle) on hareboot9 outlet 7
- located in the Gas Shed, alongside of the truck ramp into Hall A
iocha18 ( 129.57.242.118 ) - Left Arm Spectrometer position readback
- serial port on "telnet 129.57.243.202 2004" or "telnet portservha16 2004"
- "hard" reboot(AC power cycle) on hareboot10 outlet 7
- located in the Left Shield House under the Boxbeam
iocha19 ( 129.57.242.119 ) - Right Arm Spectrometer position readback
- VME crate power supply has a problem. It has been unplugged, July 16, 2019.
- serial port on "telnet 129.57.243.204 2003" or "telnet portservhawt1 2003"
- "hard" reboot(AC power cycle) on hareboot25 outlet 6
- located in the Right Shield House under the Boxbeam
iocha23 ( 129.57.36.129 ) - Compton Polarimeter laser controls
- serial port on ?
- located in the ARC building Compton laser lab (on the second floor)
iocha26 ( 129.57.242.126 ) - Polarized Helium-3 target controls
- serial port on "telnet 129.57.188.87 2008" or "telnet hatsv12 2008"
- "hard" reboot(AC power cycle) on hareboot24 outlet 8
- located in the hall, behind the green wall, by the beamline equipment racks
iocha27 ( 129.57.242.127 ) - Moller superconducting magnet controls
- serial port on "telnet 129.57.188.86 2016" or "telnet hatsv5 2016"
- "hard" reboot(AC power cycle) on hareboot6 outlet 7
- located in the beamline rack 1H75B14
iocha33 ( 129.57.242.133 ) - Polarized Helium-3 laser controls
- serial port on "telnet iocha33-serial 4000" or "telnet 129.57.242.233 4000"
- "hard" reboot(AC power cycle) on iocha33-apc outlet 1
- located in the laser lab in the rear of the Counting House
iocha48 ( 129.57.242.148 ) - Right Q1, Left Q1, and Big Box (Big Bite power supply)
- serial port on "telnet 129.57.243.203 2001" or "telnet portservha48 2001"
- "hard" reboot(AC power cycle) on hareboot7 outlet 1 ( will reboot iocha48 AND iocha48m )
- located in rack in personnel accessway (a.k.a. the labyrinth), iocha48 and iocha48m share the same VME crate
iocha48m ( 129.57.242.248 ) - Right Q1, Left Q1, and Big Box (Big Bite power supply)
- serial port on "telnet 129.57.243.203 2003" or "telnet portservha48 2003"
- "hard" reboot(AC power cycle) on hareboot7 outlet 1 ( will reboot iocha48 AND iocha48m )
- located in rack in personnel accessway (a.k.a. the labyrinth), iocha48 and iocha48m share the same VME crate
iocha49 ( 129.57.188.74 ) - Cryogenic Septum magnet controls
- serial port on "telnet 129.57.243.203 2002" or "telnet portservha48 2002"
- "hard" reboot(AC power cycle) on hareboot7 outlets 7 and 8 (hot swap power supplies)
- located in rack in personnel accessway (a.k.a. the labyrinth)
iochacp ( 129.57.242.15 ) - Compton Polarimeter controls
- serial port on "telnet 129.57.243.206 2002" or "telnet hatsv43 2002"
- located in the hall in the Compton equipment racks (1H75B18)
iochacp2 ( 129.57.242.16 ) - Compton Polarimeter controls
- serial port on "telnet 129.57.243.206 2003" or "telnet hatsv43 2003"
- located in the hall in the Compton equipment racks (1H75B18)
iocarcgcp ( 129.57.41.14 ) - Compton Polarimeter controls
- serial port on ?
- located in the laser lab in the ARC building room 213
iochacryots ( 129.57.188.84 ) - test setup for new cryo controls
- serial port on "telnet nbha4 2002" or "telnet 129.57.188.98 2002"
- "hard" reboot(AC power cycle) on hareboot27 ( 129.57.188.78 ) outlet 7
- located in rack
iochaharp1 ( 129.57.242.20 ) - Beamline harp scanners
- serial port not available
- "hard" reboot(AC power cycle) on hareboot3 outlet 7 or 8
- located in rack 1H75L12
iocharpi10 ( 129.57.188.204 ) - background monitoring
- serial port not available
- "hard" reboot(AC power cycle) on
- located in rack
iochla ( 129.57.242.2 ) - Beamline vacuum, valves and Fast Raster

no serial available to Hall A
"hard" reboot(AC power cycle) on hareboot1 outlet ? (not available to Hall A, call MCC)
"hard" reboot(AC power cycle) on hareboot3 outlet 8 (not available to Hall A, call MCC)
(master) has dual power supplies, both outlets must be cycled.
located in rack 1H75L05 in personnel accessway (a.k.a. the labyrinth)

iochla2 ( 129.57.208.91 ) - Cryo controls, Distribution Can

no serial available to Hall A
"hard" reboot(AC power cycle) on cryoreboot1.acc.jlab.org (located in rack xxxxxx) outlet 1
located in rack 1H75L05 in personnel accessway (a.k.a. the labyrinth)

iochla3 ( 129.57.242.23 ) - Beamline vacuum, ion pumps, FSD

no serial available to Hall A
"hard" reboot(AC power cycle) on hareboot3(located in rack 1H75L05) outlet 7 or 8 (not available to Hall A, call MCC)
located in rack 1H75L10 in personnel accessway (a.k.a. the labyrinth)

iochla4 ( 129.57.208.93 ) - Cryo controls, Left HRS

located in rack 1H75L06 in personnel accessway (a.k.a. the labyrinth)
no serial
"hard" reboot(AC power cycle) on cryoreboot1.acc.jlab.org (located in rack xxxxxx) outlet 3 and 4

iochla5 ( 129.57.208.94 ) - Cryo controls, Right HRS

located in rack 1H75L06 in personnel accessway (a.k.a. the labyrinth)
no serial
"hard" reboot(AC power cycle) on cryoreboot1.acc.jlab.org (located in rack xxxxxx) outlet 5 and 6

iocps1 ( 129.57.36.88 ) - use for the Moller IOC when it is in the Physics Storage building

serial port on "telnet 129.57.36.99 200x" or "telnet hatsvm1 200x"

iocse10 ( 129.57.242.3 ) - BPMs

no serial available to Hall A
"hard" reboot(AC power cycle) on hareboot3 outlet 5 (not available to Hall A, call MCC)
located in rack in personnel accessway (a.k.a. the labyrinth)

( 129.57.188.134 ) - PREX2 Beamline Thermocouples RPi

no serial available
"hard" reboot(AC power cycle) on hareboot?? outlet ??
located in rack in personnel accessway (a.k.a. the labyrinth)

( 129.57.188.135 ) - Moller Polarimeter RPi

no serial available
"hard" reboot(AC power cycle) on 129.57.188.130 outlet 2
located in rack in personnel accessway (a.k.a. the labyrinth)

( 129.57.188.136 ) - PREX2 Target Thermocouples RPi

no serial available
"hard" reboot(AC power cycle) on hareboot?? outlet ??
located in rack in personnel accessway (a.k.a. the labyrinth)

iocsofthalla - running on hlal01 machine

https://devweb.acc.jlab.org/twiki/bin/view/SWDocs/GeneralInfoOnCallHelp

nbha0 ( 129.57.242.90 ) - iocsofthalla Left Arm Digi TS8 portserver

"hard" reboot(AC power cycle) on hareboot10 outlet 6
located in the Left Shield House under the Boxbeam
Left Arm Lakeshore Gaussmeters

Port	Device
1	configured for a terminal
2	Q2 Gaussmeter
3	Q1 Gaussmeter
4	Q3 Gaussmeter
5	D1 Gaussmeter
6	D1 Teslameter (NMR)
7
8

nbha1 ( 129.57.242.91 ) - iocsofthalla Right Arm Digi TS8 portserver

"hard" reboot(AC power cycle) on hareboot25 outlet 3
located in the Right Shield House under the Boxbeam
Right Arm Lakeshore Gaussmeters

Port	Device
1	configured for a terminal
2	Q2 Gaussmeter
3	Q1 Gaussmeter
4	Q3 Gaussmeter
5	D1 Gaussmeter
6	D1 Teslameter (NMR)
7	BigBite Gaussmeter
8

nbha2 ( 129.57.242.92 ) - iocsofthalla Right Arm ICS 8065 GPIB controller

"hard" reboot(AC power cycle) on hareboot25 outlet 1
located in the Right Shield House under the Boxbeam
Right Arm HP 3458 voltmeters

GPIB Address	Device
	HP3458 voltmeter
	HP3458 voltmeter
	HP3458 voltmeter

nbha3 ( 129.57.242.93 ) - iocsofthalla Left Arm ICS 8065 GPIB controller

"hard" reboot(AC power cycle) on hareboot10 outlet 3
located in the Left Shield House under the Boxbeam
Left Arm HP 3458 voltmeters

GPIB Address	Device
	HP3458 voltmeter
	HP3458 voltmeter
	HP3458 voltmeter

nbha4 ( 129.57.242.94 ) - iocsofthalla BCM (Beam Current Monitor) ICS 8065 GPIB controller

"hard" reboot(AC power cycle) on harebootxx outlet x
located in the middle room of Counting Room A
Beam Current Monitors

GPIB Address	Device
	HP3458 voltmeter
	HP3458 voltmeter
	HP3458 voltmeter

nbha5 ( 129.57.242.95 ) - iocsofthalla Left Arm Digi TS4 portserver

"hard" reboot(AC power cycle) on hareboot30 outlet 4
located in the Left Shield House under the Boxbeam
Left Arm 18 bit DACs for Q2 and Q3 FuG power supplies

Port	Device
1	configured for a terminal
2	Q2 18 bit DAC
3	Q3 18 bit DAC
4

nbha6 ( 129.57.242.96 ) - iocsofthalla Right Arm Digi TS4 portserver

"hard" reboot(AC power cycle) on hareboot29 outlet 2
located in the Right Shield House under the Boxbeam
Right Arm 18 bit DACs for Q2 and Q3 FuG power supplies

Port	Device
1	configured for a terminal
2	Q2 18 bit DAC
3	Q3 18 bit DAC
4

nbha7 ( 129.57.242.97 ) - iocsofthalla Septum Magnets Digi TS4 portserver

"hard" reboot(AC power cycle) on hareboot6 outlet four
located behind the green wall in rack

Port	Device
1	HES power supply
2
3
4

nbha8 ( 129.57.242.98 ) - iocsofthalla Keithley Current Source (Beam Current Monitor) ICS 8065 GPIB controller

"hard" reboot(AC power cycle) on harebootxx outlet x
located in the middle room of Counting Room A
Beam Current Monitors
GPIB Address Device

Keithley Current Source

nbha9 ( 129.57.242.99 ) - iocsofthalla Left Dipole Digi TS MEI 4 port portserver

GPIB Address	Device
	Keithley Current Source

"hard" reboot(AC power cycle) on hareboot30 outlet 7
located in the Left Shield House under the Boxbeam
Octagon serial interface for Left Dipole power supply

Port	Device
1	configured for a terminal
2	LD1 Dynapower power supply Octagon microcontroller
3
4

nbha10 ( 129.57.242.100 ) - iocsofthalla Right Dipole Digi TS MEI 4 port portserver

"hard" reboot(AC power cycle) on hareboot29 outlet 7
located in the Right Shield House under the Boxbeam
Octagon serial interface for Right Dipole power supply

Port	Device
1	configured for a terminal
2	RD1 Dynapower power supply Octagon microcontroller
3
4

RPi Info for Hall A

Switched PDUs (Power Reboot Switches) Info for Hall A

**PDU: cptps2 ( 129.57.193.14 ) ( ??? )**
Outlet	Device
1
2
3
4
5
6
7
8

**PDU: cptps3 ( 129.57.193.23 ) ( under Compton light table )**
Outlet	Device
1
2
3
4
5
6
7
8

PDU: hareboot ( 129.57.243.2 )
( in Beam Line rack 1H75B05 )
(This is an Accelerator device)
Outlet	Device
1	extension cord to a power strip in rack 1H75B02
2	iochla2 slave VME crate
3	extension cord to iocse10 slave VME crate in rack 1H75B07
4	iocha1 VME crate in rack 1H75B06
5	extension cord to Calorimeter Control Chassis in rack 1H75B03
6
7
8

PDU: hareboot1 ( 129.57.243.9 )
( in Beam Line rack 1H75B0 )
(This is anAccelerator device)
Outlet	Device
1	slave crate of iochla (Cryo and Raster)
2
3
4
5
6
7
8

PDU: hareboot2 ( 129.57.243.31 )
( Left Arm Detector Stack )
Outlet	Device
1	iocha4 - Detectors Slow Controls VME
2
3
4
5	hatsv40 - portserver
6	hatsv4 - portserver
7
8

PDU: hareboot3 ( 129.57.243.10 )
( in Labyrinth )
(This is an Accelerator device)
Outlet	Device
1
2
3
4
5	iocse10 - BPMs (not available to Hall A, call MCC)
6	iochla2 - Cryo controls (not available to Hall A, call MCC)
7	iochla3 or iochaharp1 - Beamline vacuum or Beamline harp scanners
8	iochla3 or iochaharp1 - Beamline vacuum or Beamline harp scanners

**PDU: hareboot4 ( 129.57.188.50 ) ( not in use )**
Outlet	Device
1
2
3
4
5
6
7
8

**PDU: hareboot5 ( 129.57.243.15 ) ( not in use )**
Outlet	Device
1
2
3
4
5
6
7
8

PDU: hareboot6 ( 129.57.188.52 )
( beamline rack 1H75B14 )
( Moller Polarimeter )
Outlet	Device
1	hatsv5 in rack 1H75B15
2
3	Power to outlet at the pivot for target camera light
4	HES power supply
5
6
7	Moller DAQ CAMAC
8	Moller DAQ VME

PDU: hareboot7 ( 129.57.243.17 )
( in Labyrinth rack )
(This is an Accelerator device)
Outlet	Device
1	iocha48 AND iocha48m - Right Q1, Left Q1, and Big Box (Big Bite power supply)
2
3
4
5	iocha13 - Hall A Cryo Target (hot swap power supplies)
6	iocha13 - Hall A Cryo Target (hot swap power supplies)
7	iocha49 - Septum magnet controls (hot swap power supplies)
8	iocha49 - Septum magnet controls (hot swap power supplies)

PDU: hareboot9 ( 129.57.243.32 )
( in Hall A Gas Shed )
Outlet	Device
1	iocha17 - Gas Shed Slow Controls
2	Remote relay Ch2 unused
3	Ethernet hub
4
5
6
7	iocha17 power cycle
8

PDU: hareboot10( 129.57.243.33 )
( in Left Shield House under Boxbeam )
Outlet	Device
1	iocha14 - Left Arm Gantry (Q2,D,Q3) Slow Controls
2	isolated DAC (Q2/Q3)
3	Ethernet to GPIB controller for HP3458 voltmeters ( nbha3 )
4	LD1 magnet current readback (top HP3458)
5	network switch ( 240 subnet ) (sw2)
6	Port Server ( nbha0 )
7	iocha18 - Left Arm Spectrometer position readback
8	angle encoder for Spectrometer position

PDU: hareboot17 ( 129.57.243.34 )
( on Left Arm Gantry Platform )
Outlet	Device
1	Left Q1 Hall Probe LakeShore controller
2	Left Q2 Hall Probe LakeShore controller
3	Left Q3 Hall Probe LakeShore controller
4	Left D1 Hall Probe LakeShore controller
5	Left D1 NMR
6	harpileftlcw
7
8

PDU: iocha33-apc ( 129.57.188.34 )
( In Counting House Laser Lab )
Outlet	Device
1	iocha33 - Polarized Helium-3 laser controls
2
3
4
5
6
7
8

PDU: hareboot22 ( 129.57.243.35 )
( Right Arm Detector Stack )
Outlet	Device
1
2	Ethernet switch
3	iocha11 - Detectors Slow Controls VME
4
5
6
7
8

**PDU: hareboot23 ( 129.57.188.76 ) (SBS Gas System RPi in rack 1H75L06 in the Labyrinth)**
Outlet	Device
1
2
3
4
5	dsg-dev-sbc2
6	12V for I2C for sbc2
7	dsg-dev-sbc1
8	12V for I2C for sbc1

**PDU: hareboot24 ( 129.57.188.24 )**
Outlet	Device
1
2
3
4
5
6
7
8	iocha26 - Polarized Helium-3 target controls

PDU: hareboot25 ( 129.57.243.36 )
( in Right Shield House under Boxbeam )
Outlet	Device
1	Ethernet to GPIB controller for HP3458 voltmeters ( nbha2 )
2	angle encoder for Spectrometer position
3	Port Server ( nbha1 )
4	Isolated DAC for RQ2/RQ3
5	RD1 magnet current readback (middle HP3458)
6	iocha19 - Right Arm Spectrometer position readback
7	iocha16 - Right Arm Gantry (Q2,D,Q3) Slow Controls
8	network switch ( 240 subnet ) (sw3)

PDU: hareboot26 ( 129.57.192.40 )
(not in use)
Outlet	Device
1
2
3
4
5
6
7
8

PDU: hareboot27 ( 129.57.243.37 )
( on Right Arm Gantry Platform )
Outlet	Device
1	Right Q1 Lake Shore Gaussmeter (hall probe)
2	Right Q2 Lake Shore Gaussmeter (hall probe)
3	Right Q3 Lake Shore Gaussmeter (hall probe)
4	Right Dipole Lake Shore Gaussmeter (hall probe)
5
6	VME crate controlled by iochacryots
7	iochacryots - cryo test ioc
8	Right dipole NMR

PDU: hareboot29 ( 129.57.243.39 )
( in Right Shield House under Boxbeam )
Outlet	Device
1	Port Server ( portservhawt1 )
2	Port Server ( nbha6 )
3	harpirightlcw
4
5	RQ2 magnet current readback (top HP3458)
6	RQ3 magnet current readback (bottom HP3458)
7	nbha10 - iocsofthalla Right Dipole Digi TS MEI 4 port portserver
8	Right Dipole Raspberry Pi for Dynapower power supply

PDU: hareboot30 ( 129.57.243.40 )
( in Left Shield House under Boxbeam )
Outlet	Device
1	LQ2 magnet current readback (middle HP3458)
2	LQ3 magnet current readback (bottom HP3458)
3	Port Server ( portservha16 )
4	Port Server ( nbha5 )
5
6	NDX HV module
7	nbha9 - iocsofthalla Left Dipole Digi TS MEI 4 port portserver
8	NDX Pyramid Electronics

PDU: hareboot35 ( 129.57. )
( )
Outlet	Device
1	camera
2
3	fiber temps portserver ( name? )
4
5
6	fiber temp controllers
7
8	top rtd box by mark

PDU: hareboot36 ( 129.57. )
( )
Outlet	Device
1	target/oven portserver
2	target motion controller
3	air flow box
4
5
6	24v supply
7
8	oven controller box

PDU: hareboot37 ( 129.57. )
( )
Outlet	Device
1
2
3
4
5
6
7
8

PDU: ( 129.57.188.130 )
( in Moller rack in the Labyrinth )
Outlet	Device
1	Lakeshore 218 (temperature monitor)
2	Moller Polarimeter RPi ( 129.57.188.135 )
3
4
5	Moller Target controls (not the motor drives though)
6	Power supply controller (Probably should NOT reboot this remotely. If this is rebooted, the power supply will likely need to be rebooted as well)
7	Portserver
8

PDU: mapreboot ( 129.57.243.16 )
( in 9th Dipole Shed )
(This is an Accelerator device)
Outlet	Device
1	iocha2 - 9th Dipole IOC
2
3
4
5
6
7
8	NMR - Metrolab

Port Server Info for Hall A

Port Server : hatsv3 ( 129.57.164.67 )
HRSE ( Right Arm Detector Stack )
Port	Device
1	configured for a terminal
2	HRS roc1
3	HRS TS0
4	HRSE Upper LeCroy 1458
5	HRSE Lower LeCroy 1458
6	Arcnet controller VME for LeCroy high voltage(iocha22)
7	Detector Stack A Slow Controls VME (iocha11)
8
9
10
11
12
13
14
15
16

Port Server : hatsv4 ( 129.57.164.68 )
HRSH ( Left Arm Detector Stack )
Port	Device
1	configured for a terminal
2	HRS roc2
3	HRS roc3
4	HRS TS1
5
6	LeCroy high voltage mainframe
7	HRS TS11
8

Port Server : hatsv5 ( 129.57.188.86 )
beamline rack 1H75B15
Port	Device
1	configured for a terminal
2	e-P 1
3	Moller 1 (formerly hac41)
4	Moller 2 (VME 2306 DAQ)
5	e-P 2
6	Compton roc1
7	Compton roc2
8	Compton roc3
9	Compton roc4
10	Compton roc5
11	Beamline HV
12
13	ARC energy
14	HRS roc14
15	HRS roc15
16

Port Server : hatsv12 ( 129.57.188.87 )
beamline
Port	Device
1	configured for a terminal
2
3
4
5
6
7
8	iocha26 (Polarized He-3 Target)

Port Server : hatsv14 ( 129.57.243.200 )
Hall A Gas Shed
Port	Device
1	configured for a terminal
2	iocha17
3
4
5
6
7
8

Port Server : hatsv40 ( 129.57.243.201 )
Left Detector Stack
Port	Device
1	configured for a terminal
2
3	iocha4 - Left Detector Stack Slow Controls VME
4	iocha3 - RICH DAQ IOC
5
6
7
8

Port Server : hatsv42 ( 129.57.243.205 )
Beamline Rack 1H75B09
Port	Device
1	configured for a terminal
2	iocha12 (beamline slow controls)
3
4

Port Server : hatsv43 ( 129.57.243.206 )
Compton Rack ( 1H75B18 )
Port	Device
1	configured for a terminal
2	iochacp (Compton Polarimeter light table controls)
3
4

Port Server : hatsvm1 ( 129.57.41.30 )
Moller Target test setup
Port	Device
1	configured for a terminal
2
3
4
5
6
7
8

Port Server : iocha33-serial ( 129.57.242.233 )
Polarized He-3 Laser Lab in the Counting House
Port	Device
1	configured for a terminal
2
3
4
5
6
7
8

Port Server : portservha16 ( 129.57.243.202 )
Left Arm in the Shield House under the Boxbeam
Port	Device
1	iocha9 - Left Arm Bogie Controls
2	iocha14 - Left Arm Gantry (Q2,D,Q3) Slow Controls
3	UPS - unknown type
4	iocha18 - Left Arm Spectrometer position readback

Port Server : portservhawt1 ( 129.57.243.204 )
Right Arm in the Shield House under the Boxbeam
Port	Device
1	iocha10 - Right Arm Bogie Controls
2	iocha16 - Right Arm Gantry (Q2,D,Q3) Slow Controls
3	iocha19 - Right Arm Spectrometer position readback
4	UPS - Liebert PowerSuite 1400
5	iocha11 - Right Detector Stack Slow Controls
6
7
8

Port Server : portservha48 ( 129.57.243.203 )
In the labyrinth in rack 1H75L04
Port	Device
1	iocha48 - Right Q1, Left Q1, and Big Box (Big Bite power supply)
2	iocha49 - Septum magnet controls
3	iocha48m - Right Q1, Left Q1, and Big Box (Big Bite power supply)
4	iocha13 - Cryo Target

Back to Jack's Notes