The start of this chapter of the apcupsd manual in HTML format was pulled from the Network UPS Tools (NUT) site. It has been an invaluable tool in improving apcupsd, and I consider it the Bible of APC UPS programming. In the course of using it, I have added information gleaned from apcupsd and information graciously supplied by APC. Hopefully, the additions made herein can benefit the original author and his programming project, and maybe some day, the Apcupsd project and the NUT project can join forces.
Originally this evil hack was used to connect the UPS to the PC when this page was first being built. As you can see, I cheated and neglected the ground (only 2 wires!) and it still worked. This method can be used for playing around, but for professional systems this is obviously not a viable option.
That hack didn't work out so well (damned cats), so it was retired quite awhile back. The most practical solution was to go out and BUY the DOS/Win version of PowerChute just for the black (smart) cable. I recommend doing the same thing if you actually care about this thing working properly. Of course, if you have one of the newer packages that came with PowerChute, you already have the cable you need.
Many thanks to Steve Draper for providing this scan.
For additional information on cables, see the cables section of this manual.
The following table describes the single character Code or command that you can send to the UPS, its meaning, and what sort of response the UPS will provide. Typically, the response shown below is followed by a newline (\n in C) and a carriage return (\r in C). If you send the UPS a command that it does not recognize or that is not available on your UPS, it will normally respond by "NA" for not available, otherwise the response is given in the "Typical results" column.
| Code | Meaning | Typical results |
|---|---|---|
| ^A | Model string | SMART-UPS 700 |
| ^N | Turn on UPS (send twice, with > 1.5s delay between chars) Only on 3rd gen SmartUPS and Black Back-UPS Pros | n/a |
| ^Z | Permitted EEPROM Values | A large string (254 chars) that gives the EEPROM permitted values for your model. For details see below. |
| A | Front panel test | Light show + "OK" (and 2s beep) |
| B | Battery voltage | Ranges - typical "27.87" |
| C | Internal temperature (degrees C) | Ranges - typical "036.0" |
| D | Runtime calibration - runs until battery is below 25% (35% for Matrix) This updates the 'j' values - only works at 100% battery charge Can be aborted with a second "D" | ! when on battery, $ on line |
| E | Automatic self test intervals | Default = 336 (336 hours = 14 days) (336=14 days, 168=7 days, ON=power on, OFF=never) |
| F | Line frequency, Hz | 60.00 (50.0 in Europe) |
| G | Cause of transfer | R = unacceptable utility voltage rate of change, H = high utility voltage, L = low utility voltage, T = line voltage notch or spike, O = no transfers yet (since turnon), S = transfer due to serial port U command or activation of UPS test from front panel, NA = transfer reason still not available (read again). |
| K--K | Shutdown with grace period (set with 'p') - need > 1.5s between first and second K | Matrix/3rd gen SmartUPS/Black Back-UPS Pros: "OK", all others: "*" |
| L | Input line voltage | Ranges - typical "118.3" or "228.8" in Europe |
| M | Maximum line voltage received since last M query | Ranges - typical "118.9" or "230.1" in Europe |
| N | Minimum line voltage received since last N query | Ranges - typical "118.9" or "226.2" in Europe |
| O | Output voltage | Ranges - typical "118.3" or "228.8" in Europe |
| P | Power load % | Ranges - typical "011.4" depends on what you have plugged in. |
| Q | Status flags | Bitmapped, see below |
| R | Turn dumb Only on 3rd gen SmartUPS, SmartUPS v/s, BackUPS Pro | "BYE" |
| S | Soft shutdown after 'p' delay, return online when power returns Only works when UPS is on battery | OK |
| U | Simulate power failure | !! when switching to battery, then $ when back on line |
| V | Old firmware revision | "GWD" or "IWI" The last character indicates the locale (Domestic, International). |
| W | Self test (battery), results stored in "X" | "OK" |
| X | Results of last self test | "OK" - good battery, "BT" - failed due to insufficient capacity, "NG" - failed due to overload, "NO" - no results available (no test performed in last 5 minutes) |
| Y | Enter smart mode | "SM" |
| Z--Z | Shutdown immediately (no delay) - need > 1.5s between first and second Z | N/A |
| a | Show protocol version.alert messages.valid commands (delimited by periods) | "3.!$%+?=#|.^A^N^Z+-789<@ABCDEFGKLMNOPQRSUVWXYZ'abcefgjklmnopqrsuvzy~^?" - Link-Level.alert-messages.commands |
| b | Firmware revision | "50.9.D" - 50 = SKU (variable length), 9 = firmware revision, D = country code (D=USA, I=International, A=Asia, J=Japan, M=Canada) |
| c | UPS local id | UPS_IDEN (you can program any 8 characters here) |
| e | Return threshold | % battery charge threshold for return (00=00%, 01=15%, 02=25%, 03=90%) |
| f | Battery level % | Ranges - typical "100.0" when fully charged as should normally be the case |
| g | Nominal battery voltage (not actual voltage - see B) | "012" or "024" or "048". |
| h | Measure-UPS: ambient humidity (%) | "nnn.n" - percentage |
| i | Measure-UPS: dry contacts | 10 = contact 1, 20 = 2, 40 = 3, 80 = 4 |
| j | Estimated runtime at current load (minutes) | "0112:" (note, it is terminated with a colon) |
| k | Alarm delay | 0(zero) = 5 second delay after fail, T = 30 second delay, L = alarm at low battery only, N = no alarm |
| l | Low transfer voltage | Default "103" or "208" in Europe |
| m | Manufacturing date | Unique within groups of UPSes (production runs) |
| n | Serial number | Unique for each UPS |
| o | Nominal Output Voltage | The Nominal Output Voltage when running on batteries. Default "115" or "230" in Europe. |
| p | Shutdown grace delay, seconds | Default "020" (020/180/300/600) |
| q | Low battery warning, minutes | Default "02" |
| r | Wakeup delay (time) - seconds | Default "000" (000/060/180/300) |
| s | Sensitivity | "H" - highest, "M" - medium, "L" - lowest, "A" - autoadjust (Matrix only) |
| u | Upper transfer voltage | Default "132" or "253" in Europe |
| t | Measure-UPS: ambient temperature (degrees C) | "nn.nn" |
| x | Last battery change | Eight characters. Varies typically dd/mm/yy - 31/12/99 |
| y | Copyright notice | "(C) APCC" - only works if firmware letter (from "V") is later than O |
| z | Reset the EEPROM to factory settings (but not ident or batt replacement date) Not on SmartUPS v/s or BackUPS Pro | "CLEAR" |
| + | Capability cycle | Cycle forward through possible values ("|" from UPS afterward to confirm change). Do not use this unless you know how to program your UPS EEPROM or you may damage your UPS. |
| - | Capability cycle | Cycle backward through possible values ("|" from UPS afterward to confirm change)Do not use this unless you know how to program your UPS EEPROM or you may damage your UPS. |
| @nnn | Shutdown (after delay 'p') with delayed wakeup of nnn tenths of an hour (after 'r' time) | Matrix/3rd gen UPS: "OK", others "*" |
| 0x7f (DEL key) | Abort shutdown - use to abort @, S, K--K | "OK" |
| ~ | Register #1 | See below |
| ' | Register #2 | See below |
| 0 | Battery constant | Set to A0 on SmartUPS 1000 with new battery |
| 4 | ??? | Prints 35 on SmartUPS 1000 |
| 5 | ??? | Prints EF on SmartUPS 1000 |
| 6 | ??? | Prints F9 on SmartUPS 1000 |
| 7 | Dip switch positions (if applicable) | See below |
| 8 | Register #3 | See below |
| 9 | Line quality | "FF" acceptable, "00" unacceptable |
| > | Number of external battery packs attached | SmartCell models: "nnn" where nnn is how many external
packs are connected Non-SmartCell units: whatever has been set with >+ and >- by the user |
| Matrix UPS (and possibly Symmetra) specific commands | ||
| ^ | Run in bypass mode | If online, "BYP" is received as bypass mode starts If already in bypass, "INV" is received and UPS goes online "ERR" received if UPS is unable to transfer |
| < | Number of bad battery packs | "nnn" - count of bad packs connected to the UPS |
| / | Load current | "nn.nn" - true RMS load current drawn by UPS |
| \ | Apparent load power | "nnn.nn" - output load as percentage of full rated load in VA. |
| ^V | Output voltage selection (editable) | "A" - automatic according to input tap, "M" - 208 VAC, "I" - 240 VAC |
| ^L | Front panel language | "E" - English, "F" - French, "G" - German, "S" - Spanish, "1" "2" "3" "4" - ? |
| w | Run time conservation | "NO" (disabled) or "02" "05" "08" - minutes of runtime to leave in battery (UPS shuts down "early") |
| Bit | Switch | Option when bit=1 |
|---|---|---|
| 0 | 4 | Low battery alarm changed from 2 to 5 mins. Autostartup disabled on SU370ci and 400 |
| 1 | 3 | Audible alarm delayed 30 seconds |
| 2 | 2 | Output transfer set to 115 VAC (from 120 VAC) or to 240 VAC (from 230 VAC) |
| 3 | 1 | UPS desensitized - input voltage range expanded |
| 4-7 | - | Unused at this time |
| Bit | Hex Bit | Meaning |
|---|---|---|
| 0 | 0x01 | 1 = Runtime calibration occurring
Not reported by Smart UPS v/s and BackUPS Pro |
| 1 | 0x02 | 1 = SmartTrim
Not reported by 1st and 2nd generation SmartUPS models |
| 2 | 0x04 | 1 = SmartBoost |
| 3 | 0x08 | 1 = On line (this is the normal condition) |
| 4 | 0x10 | 1 = On battery |
| 5 | 0x20 | 1 = Overloaded output |
| 6 | 0x40 | 1 = Battery low |
| 7 | 0x80 | 1 = Replace battery |
| Character | Description |
|---|---|
| ! | Line Fail - sent when the UPS goes on-battery, repeated every 30 seconds until low battery condition reached. Sometimes occurs more than once in the first 30 seconds. |
| $ | Return from line fail - UPS back on line power, only sent if a ! has been sent. |
| % | Low battery - Sent to indicate low battery, but not on SmartUPS v/s or BackUPS Pro models |
| + | Return from low battery - Sent when the battery has been recharged to some level only if a % has been sent previously |
| ? | Abnormal condition - sent for conditions such as "shutdown due to overload" or "shutdown due to low battery capacity". Also occurs within 10 minutes of turnon. |
| = | Return from abnormal condition - Sent when the UPS returns from an abnormal condition where ? was sent, but not a turn-on. Not implemented on SmartUPS v/s or BackUPS Pro models. |
| * | About to turn off - Sent when the UPS is about to switch off the load. No commands are processed after this character is sent. Not implemented on SmartUPS v/s, BackUPS Pro, or 3rd generation SmartUPS models. |
| # | Replace battery - Sent when the UPS detects that the battery needs to be replaced. Sent every 5 hours until a new battery test is run or the UPS is shut off. Not implemented on SmartUPS v/s or BackUPS Pro models. |
| & | Check alarm register for fault (Measure-UPS) - sent to signal that temp or humidity out of set limits. Also sent when one of the contact closures changes states. Sent every 2 minutes, stops when the alarm conditions are reset. Only sent for alarms enabled with I. Cause of alarm may be determined with J. Not on SmartUPS v/s or BackUPS Pro. |
| | | Variable change in EEPROM - Sent whenever any EEPROM variable is changed. Only supported on Matrix UPS and 3rd generation SmartUPS models. |
| Bit | Hex Bit | Meaning |
|---|---|---|
| 0 | 0x01 | In wakeup mode (typically lasts < 2s) |
| 1 | 0x02 | In bypass mode due to internal fault - see register 2 or 3 |
| 2 | 0x04 | Going to bypass mode due to command |
| 3 | 0x08 | In bypass mode due to command |
| 4 | 0x10 | Returning from bypass mode |
| 5 | 0x20 | In bypass mode due to manual bypass control |
| 6 | 0x40 | Ready to power load on user command |
| 7 | 0x80 | Ready to power load on user command or return of line power |
| Bit | Meaning |
|---|---|
| 0 | Fan failure in electronics, UPS in bypass |
| 1 | Fan failure in isolation unit |
| 2 | Bypass supply failure |
| 3 | Output voltage select failure, UPS in bypass |
| 4 | DC imbalance, UPS in bypass |
| 5 | Command sent to stop bypass with no battery connected - UPS still in bypass |
| 6 | Relay fault in SmartTrim or SmartBoost |
| 7 | Bad output voltage |
| Bit | Meaning |
|---|---|
| 0 | Output unpowered due to shutdown by low battery |
| 1 | Unable to transfer to battery due to overload |
| 2 | Main relay malfunction - UPS turned off |
| 3 | In sleep mode from @ (maybe others) |
| 4 | In shutdown mode from S |
| 5 | Battery charger failure |
| 6 | Bypass relay malfunction |
| 7 | Normal operating temperature exceeded |
Old Firmware revision and model ID String for SmartUPS & MatrixUPS
This is a three character string XYZ
where X == Smart-UPS or Matrix-UPS ID Code.
range 0-9 and A-P
1 == unknown
0 == Matrix 3000
5 == Matrix 5000
the rest are Smart-UPS and Smart-UPS-XL
2 == 250 3 == 400 4 == 400
6 == 600 7 == 900 8 == 1250
9 == 2000 A == 1400 B == 1000
C == 650 D == 420 E == 280
F == 450 G == 700 H == 700XL
I == 1000 J == 1000XL K == 1400
L == 1400XL M == 2200 N == 2200XL
O == 3000 P == 5000
where Y == Possible Level of Smart Features, unknown???
G == Stand Alone
T == Stand Alone
V == ???
W == Rack Mount
where Z == National Model Use Only Codes
D == Domestic 115 Volts
I == International 230 Volts
A == Asia ?? 100 Volts
J == Japan ?? 100 Volts
New Firmware revison and model ID String in NN.M.L is the format
where NN == UPS ID Code.
12 == Back-UPS Pro 650
13 == Back-UPS Pro 1000
52 == Smart-UPS 700
60 == SmartUPS 1000
72 == Smart-UPS 1400
where NN now Nn has possible meanings.
N == Class of UPS
1n == Back-UPS Pro
5n == Smart-UPS
7n == Smart-UPS NET
n == Level of intelligence
N1 == Simple Signal, if detectable WAG(*)
N2 == Full Set of Smart Signals
N3 == Micro Subset of Smart Signals
where M == Possible Level of Smart Features, unknown???
1 == Stand Alone
8 == Rack Mount
9 == Rack Mount
where L == National Model Use Only Codes
D == Domestic 115 Volts
I == International 230 Volts
A == Asia ?? 100 Volts
J == Japan ?? 100 Volts
M == North America 208 Volts (Servers)
#uD43132135138129uM43229234239224uA43110112114108 ....
It looks bizarre and ugly, but is easily parsed. The # is some kind of marker/ident character. Skip it. The rest fits this form:
Matrix-UPS models have ## between each grouping for some reason.
Here is an example broken out to be more readable:
CMD DFO RSP FSZ FVL
u D 4 3 127 130 133 136
u M 4 3 229 234 239 224
u A 4 3 108 110 112 114
u I 4 3 253 257 261 265
l D 4 3 106 103 100 097
l M 4 3 177 172 168 182
l A 4 3 092 090 088 086
l I 4 3 208 204 200 196
e 4 4 2 00 15 50 90
o D 1 3 115
o J 1 3 100
o I 1 3 230 240 220 225
o M 1 3 208
s 4 4 1 H M L L
q 4 4 2 02 05 07 10
p 4 4 3 020 180 300 600
k 4 4 1 0 T L N
r 4 4 3 000 060 180 300
E 4 4 3 336 168 ON OFF
CMD == UPSlink Command.
u = upper transfer voltage
l = lower transfer voltage
e = return threshold
o = output voltage
s = sensitivity
p = shutdown grace delay
q = low battery warning
k = alarm delay
r = wakeup delay
E = self test interval
DFO == (4)-all-countries (D)omestic (I)nternational (A)sia (J)apan
(M) North America - servers.
RSP == Total number possible answers returned by a given CMD.
FSZ == Max. number of field positions to be filled.
FVL == Values that are returned and legal.
| Item | Command | Meaning |
|---|---|---|
| 1. | c | The UPS Id or name |
| 2. | x | The last date the batteries were replaced |
| 3. | u | The Upper Transfer Voltage |
| 4. | l | The Lower Transfer Voltage |
| 5. | e | The Return Battery Charge Percentage |
| 6. | o | The Output Voltage when on Batteries |
| 7. | s | The Sensitivity to Line Quality |
| 8. | p | The Shutdown Grace Delay |
| 9. | q | The Low Battery Warning Delay |
| 10. | k | The Alarm Delay |
| 11. | r | The Wakeup Delay |
| 12. | E | The Automatic Self Test Interval |
The first two cases (Ident and Batt date) are somewhat special in that you tell the UPS you want to change the value, then you supply 8 characters that are saved in the EEPROM. The last ten item are programmed by telling the UPS that you want it to cycle to the next permitted value.
In each case, you indicate to the UPS that you want to change the EEPROM by first sending the appropriate query command (e.g. "c" for the UPS ID or "u" for the Upper Transfer voltage. This command is then immediately followed by the cycle EEPROM command or "-". In the case of the UPS Id or the battery date, you follow the cycle command by the eight characters that you want to put in the EEPROM. In the case of the other ten items, there is nothing more to enter.
The UPS will respond by "OK" and approximately 5 seconds later by a vertical bar (|) to indicate that the EEPROM was changed.
Pavel Korensky <pavelk@dator3.anet.cz>,
Andre M. Hedrick <hedrick@suse.de>,
Christopher J. Reimer <reimer@doe.carleton.ca>,
Kevin D. Smolkowski <kevins@trigger.oslc.org>,
Werner Panocha <wpanocha@t-online.de>,
Steven Freed,
Russell Kroll.
additions by:
Kern Sibbald <apcupsd-devel@apcupsd.org> 21 December 1999additional credits by:
Riccardo Facchetti
08 February 2000
