ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
    º    Lesson 1 Part 10.0   F-PC 3.5 Tutorial by Jack Brown   º
    ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
                      ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
                      ³  Loading  Files ³
                      ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

Here is yet another way to load the entire file, and it works even if
the file is not currently open is to use the FLOAD command that we used
before.

FLOAD BANNER <enter>    <--- This one requires the file name.

Note:  If the currently open file is not BANNER.SEQ but some other
       file say XXX.SEQ , then when the FLOADing above is finished
       the file XXX.SEQ will be restored as the currently open file.

                 ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
                 ³   **** Handy TIP ****  ³
                 ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

A common mistake made by the novice is to repeatedly LOAD the same file
several times while testing different load techniques as above or while
reloading a corrected or modified version of a program under
development.  If you are getting a lot of ... " isn't unique " messages
it is probably because you are loading multiple copies of the same file
on top of one another.  To empty the dictionary of the words previously
loaded take one of the following approaches.

To remove all of the words so you are back to the state when F-PC was
started you should type:

EMPTY <enter>     <---  remove all words added since starting F-PC

To remove all of the words in the BANNER program only you must FORGET
the first word defined in the BANNER program. The first word in the
BANNER program is CHAR-MATRIX , thus typing:

FORGET CHAR-MATRIX <enter>  <--- will remove CHAR-MATRIX and all the
                                 following words from the dictionary.
This would be the best approach if you had added other words earlier
that you still want to retain.

               ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
               ³   Make Your Own Banner!   ³
               ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

Enter the EDitor and open a new file  MYBANNER.SEQ.

Use the <ALT> N   entry....  its the fastest.

Type in the following definition, using the <enter> key to add new lines
to the file as needed.  The arrow keys can be used to move around, but
you will not be allowed to move below the line containing the little up
pointing triangle at the left edge of the screen, as this represents the
end of the current file.  YOURNAME must be no longer than 11 characters!

: GREETING      ( --- )
     DARK CR    " HELLO"    BANNER  " FROM" BANNER
     2 SECONDS  " YOURNAME" BANNER ;

Now that you have typed in or edited the above definition into the file
MYBANNER.SEQ, leave the editor saving the text you have entered, by
pressing SHIFT F10 to save the program. If you already have the file
BANNER loaded/compiled you are ready to compile the file MYBANNER with
your GREETING . Type:

FLOAD MYBANNER <enter>     <--- to compile your banner greeting
GREETING       <enter>     <--- to execute your banner greeting

( *****  DID you load BANNER.SEQ first???  )

ÖÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ·
º  Problem 1.6   º
ÓÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĽ
The banner program uses the # character to form the block letters. Study
the banner program and find where the change(s) must be made so that the
block letters come out using the 177 character that was used to make the
word WHITE in our checker board program. While your at it find out what
you must do to stop the demo from running when the program is compiled.
First one to report back here with exactly what must be changed wins a
prize! Also,  What will the following do if typed at the dos prompt?

C:\FPC> F BANNER OK FLOAD MYBANNER GREETING BYE  <enter>  <--- Whatsitdo?
Sorry, that's the wrong answer.  It doesn't do what I thought either!

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Please move to Lesson 1 Part 11.0  ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ