| Common Name: | TYGON B-44-3 |
| Manufacturer: | SAINT-GOBAIN PERFORMANCE PLASTICS |
| MSDS Revision Date: | 9/26/2006 |
| Grainger Item Number(s): | 2LPR5, 2LPR6, 2LPR7, 2LPR8, 2LPR9, 2LPT1, 2LPT2, 2LPT3, 2LPT4, 2LPT5, 2LPT6, 2LPT7, 2LPT8, 2LPT9, 2LPU1, 2LPU2, 2LPU3, 2LPU4, 2LPU5, 2LPU6, 2LPU7, 2LPU8, 2LPU9, 2LPV1, 2LPV2, 2LPV3, 2LPV4, 2LPV5, 2LPV6, 2LPV7, 2LPV8, 2LPV9, 2LPW1, 2LPW2, 2LPW3, 2LPW4, 2LPW5, 2LPW6, 2LPW7, 2LPW8 |
| Manufacturer Model Number(s): |
MSDS Table of Contents
Click the desired link below to jump directly to that section in the MSDS.
MATERIAL SAFETY DATA SHEET
PRODUCT: TYGON(R*) B-44-3
MANUFACTURERS NAME: SAINT-GOBAIN PERFORMANCE PLASTICS
ADDRESS:
2664 GILCHRIST RD.
AKRON, OHIO 44305
EMERGENCY TELEPHONE NUMBER:
CALL CHEMTEL:
1-800-255-3924 USA
1-813-248-0585 INTERNATIONAL
DATE PREPARED: 9/26/06
| SECTION 1 - IDENTITY |  |
1.1 COMMON NAME (USED ON LABEL): TYGON(R*) B-44-3
1.2 CHEMICAL NAME: N/A
1.3 CHEMICAL FAMILY: POLYVINYL CHLORIDE/COMPOUNDED ORGANIC POLYMER
1.4 FORMULA:
THE SPECIFIC CHEMICAL IDENTITY OF THE INGREDIENTS IS CONSIDERED A TRADE
SECRET.
IN REFERENCE TO 40CFR, SECTION 313, PART 372, COMMUNITY RIGHT TO KNOW,
WE CLASSIFY TYGON(R*) TUBING AS AN "ARTICLE" AND THEREFORE NOT SUBJECT
TO NOTIFICATION REQUIREMENTS.
| SECTION 2 - HAZARDOUS INGREDIENTS | |
2.1 PRINCIPAL HAZARDOUS COMPONENT(S) THRESHOLD LIMIT VALUE
(CHEMICAL & COMMON NAMES)
A. DI-2-ETHYLHEXYL PHTHALATE (DOP OR DEHP) 5 MG/M3
2.2 PRINCIPAL NON-HAZARDOUS COMPONENT(S) THRESHOLD LIMIT VALUE
(CHEMICAL & COMMON NAMES)
ALL ADDITIVES ARE PHYSICALLY BOUND IN THE MANUFACTURING PROCESS AND ARE NOT
EXPECTED TO CREATE ANY HAZARD WHEN THE PRODUCT IS USED IN ACCORDANCE WITH
NORMAL MANUFACTURING AND INDUSTRIAL HYGIENE PRACTICE AND BY FOLLOWING THE
GUIDELINES ON THIS SHEET.
| SECTION 3 - PHYSICAL & CHEMICAL CHARACTERISTICS | |
(FIRE & EXPLOSION DATA)
3.1 BOILING POINT: N/A
3.2 SPECIFIC GRAVITY (H2O = 1): 1.20
3.3 VAPOR PRESSURE: 7 X 10(-8) MMHg, 20 DEG. C
3.4 PERCENT VOLATILE BY VOLUME: N/A
3.5 VAPOR DENSITY (AIR = 1): N/A
3.6 EVAPORATION RATE: N/A
3.7 SOLUBILITY IN WATER: NEGLIGIBLE
3.8 MELTING POINT: N/A
3.9 APPEARANCE AND ODOR: CLEAR TUBING; SLIGHT ODOR.
3.10 FLASH POINT: 500 DEG. F (260 DEG. C)
3.11 FLAMMABLE LIMITS IN AIR BY VOLUME:
LOWER: N/A
UPPER: N/A
3.12 AUTO-IGNITION TEMPERATURE: N/A
3.13 EXTINGUISHER MEDIA: WATER
3.14 SPECIAL FIRE FIGHTING PROCEDURES:
FIRE FIGHTERS SHOULD WEAR FULL PROTECTIVE CLOTHING INCLUDING A
SELF-CONTAINED BREATHING APPARATUS.
3.15 UNUSUAL FIRE & EXPLOSION HAZARDS: NONE KNOWN
| SECTION 4 - PHYSICAL HAZARDS | |
4.1 STABILITY:
STABLE (X)
UNSTABLE ( )
CONDITIONS TO AVOID:
TEMPERATURES ABOVE 300 DEG. F WILL SLOWLY DECOMPOSE THE TUBING MATERIAL
RESULTING IN THE LIBERATION OF HCl GAS.
4.2 INCOMPATIBILITY: NONE KNOWN
4.3 HAZARDOUS DECOMPOSITION PRODUCTS:
WHEN FORCED TO BURN, PVC COMPOUNDS WILL MAINLY CONTRIBUTE CO, CO2, AND HCl
AS GASES.
4.4 HAZARDOUS POLYMERIZATION:
MAY OCCUR ( )
WILL NOT OCCUR (X)
CONDITIONS TO AVOID: NONE KNOWN
| SECTION 5 - HEALTH HAZARDS | |
5.1 THRESHOLD LIMIT VALUE: N/E
5.2 SIGN & SYMPTOMS OF EXPOSURE:
1. ACUTE OVEREXPOSURE:
TOXICOLOGICAL TESTING HAS NOT BEEN CONDUCTED WITH THIS MATERIAL.
ROUTE OF ENTRY:
EYE CONTACT: SEE INHALATION
SKIN CONTACT:. SEE INHALATION
INHALATION:
AT TEMPERATURES ABOVE 300 DEG. F, FUMES MAY BE EMITTED THAT ARE IRRITATING
TO RESPIRATORY TRACT, EYES, OR SKIN OF SENSITIVE PEOPLE.
INGESTION: N/A
2. CHRONIC OVEREXPOSURE: NONE KNOWN
5.3 MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:
THERE ARE NO DATA AVAILABLE WHICH ADDRESS MEDICAL CONDITIONS WHICH ARE
GENERALLY RECOGNIZED AS BEING AGGRAVATED BY EXPOSURE TO THIS PRODUCT.
5.4 CHEMICAL LISTED AS CARCINOGEN OR POTENTIAL CARCINOGEN:
NATIONAL TOXICOLOGY PROGRAM:
YES:
NO:
I.A.R.C. MONOGRAPHS:
YES:
NO:
OSHA:
YES: SUSPECTED
NO:
CALIF. PROP. 65:
YES: DEHP
5.5 OSHA PERMISSIBLE EXPOSURE LIMIT: 5 MG/M3 TWA
5.6 ACGIH THRESHOLD LIMIT VALUE: 5 MG/M3 TWA, 10 MG/M3 STEL
5.7 OTHER EXPOSURE LIMIT USED: UNKNOWN
5.8 EMERGENCY & FIRST-AID PROCEDURES:
INHALATION:
IF IRRITATION OCCURS, REMOVE AFFECTED INDIVIDUAL FROM AREA, REFER TO
PHYSICIAN.
EYES: N/A
SKIN: N/A
INGESTION: N/A
| SECTION 6 - SPECIAL PROTECTION INFORMATION | |
6.1 RESPIRATORY PROTECTION: N/R
6.2 VENTILATION:
LOCAL EXHAUST: N/R
MECHANICAL-GENERAL: N/R
MECHANICAL-SPECIAL: N/R
MECHANICAL-OTHER: N/R
6.3 PROTECTIVE GLOVES: N/R
6.4 EYE PROTECTION: N/R
6.5 OTHER PROTECTIVE CLOTHING OR EQUIPMENT: NOT NECESSARY
| SECTION 7 - SPECIAL PRECAUTIONS AND SPILL/LEAK PROCEDURES | |
7.1 PRECAUTIONS TO BE TAKEN IN HANDLING & STORAGE: STORE COOL AND DRY.
7.2 OTHER PRECAUTIONS: N/A
7.3 STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: N/A
7.4 WASTE DISPOSAL METHODS:
ACCORDING TO LOCAL, STATE AND FEDERAL REGULATIONS.
| SECTION 8 - OTHER INFORMATION | |
8.1 TRANSPORTATION INFORMATION:
DOT SHIPPING NAME: N/A
DOT HAZARD CLASS: N/A
DOT LABEL(S): N/A
UN/NA NUMBER: N/A
PLACARDS: NONE
IATA: N/A
IMO IMDG-CODE: N/A
EUROPEAN CLASS:
RID (OCTI): N/A
ADR (ECE): N/A
RAR (IATA): N/A
8.2 THE INFORMATION AND RECOMMENDATIONS SET FORTH HEREIN ARE TAKEN FROM
SOURCES BELIEVED TO BE ACCURATE AS OF THE DATE HEREOF, HOWEVER,
SAINT-GOBAIN PERFORMANCE PLASTICS CORPORATION MAKES NO WARRANTY WITH
RESPECT TO THE ACCURACY OF THE INFORMATION OR THE SUITABILITY OF THE
RECOMMENDATIONS, AND ASSUMES NO LIABILITY TO ANY USER THEREOF.
FORM #: N0123.1
N/E = NOT ESTABLISHED
N/A = NOT APPLICABLE
N/R = NOT REQUIRED
N/D = NOT DETERMINED