Difference between revisions of "Polhe3 meeting 20110907"
From Hall A Wiki
| Line 3: | Line 3: | ||
*** The first cell has not been filled due to some complications in the gas system. The second cell is not delivered and won't be until the first one is filled. Alan is working on oven bottom piece. | *** The first cell has not been filled due to some complications in the gas system. The second cell is not delivered and won't be until the first one is filled. Alan is working on oven bottom piece. | ||
** temperature optimization test (all) | ** temperature optimization test (all) | ||
| − | *** | + | *** Did the Q-curve for water calibration |
| + | *** Did the sensitivity test of Lock—in and linear magnifying quality of preamplifier， Chunhua will compare measured data （Jie， Chunhua） | ||
*** Checked fitting with error estimation, in preparation for notes (Chunhua) | *** Checked fitting with error estimation, in preparation for notes (Chunhua) | ||
| − | |||
** pulse NMR (all) | ** pulse NMR (all) | ||
| − | *** | + | *** Jie wrote the labview program for DAQ (Jie) |
| − | + | ** Diffusion mode measurement (all) | |
| − | ** | + | *** Made the zapper coil （Chunhua） |
| − | *** | + | |
| − | + | ||
| − | + | ||
| − | + | ||
| Line 26: | Line 22: | ||
| align="center" colspan="4" | new cell and oven bottom piece | | align="center" colspan="4" | new cell and oven bottom piece | ||
|- | |- | ||
| − | | 9/ | + | | 9/21-10/5 |
| receiving and check fitting | | receiving and check fitting | ||
| all | | all | ||
| Line 33: | Line 29: | ||
| align="center" colspan="4" | diffusion mode measurement | | align="center" colspan="4" | diffusion mode measurement | ||
|- | |- | ||
| − | | 9/ | + | | 9/21-10/5 |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| do the test | | do the test | ||
| all | | all | ||
| Line 45: | Line 36: | ||
| align="center" colspan="4" | convection flow study | | align="center" colspan="4" | convection flow study | ||
|- | |- | ||
| − | | 9/ | + | | 9/21-10/5 |
| make a zapper coil or a pair of coils to confine field better | | make a zapper coil or a pair of coils to confine field better | ||
| Chunhua | | Chunhua | ||
| | | | ||
|- | |- | ||
| − | | 9/ | + | | 9/21-10/5 |
| do calibration on old and new RTD. connect RTD readout/control in labview | | do calibration on old and new RTD. connect RTD readout/control in labview | ||
| Jie | | Jie | ||
| Line 57: | Line 48: | ||
| align="center" colspan="4" | temperature optimization test | | align="center" colspan="4" | temperature optimization test | ||
|- | |- | ||
| − | | 9/ | + | | 9/21-10/05 |
| − | | | + | | find a removable pick-up coil to do another water calibration for future NMR test |
| all | | all | ||
|- | |- | ||
| − | | 9/ | + | | 9/21-10/05 |
| improve analysis, check fitting with error estimation and prepare plots for a note. | | improve analysis, check fitting with error estimation and prepare plots for a note. | ||
| Chunhua | | Chunhua | ||
| Line 68: | Line 59: | ||
| align="center" colspan="4" | pulse NMR | | align="center" colspan="4" | pulse NMR | ||
|- | |- | ||
| − | | 9/ | + | | 9/21-10/05 |
| − | | pNMR setup | + | | pNMR setup and test |
| Jie | | Jie | ||
| | | | ||
|- | |- | ||
| − | | 9/ | + | | 9/21-10/05 |
| find or make coil and test it with capacitor matchbox | | find or make coil and test it with capacitor matchbox | ||
| Chunhua | | Chunhua | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| | | | ||
|} | |} | ||
Revision as of 09:20, 25 September 2011
- progress
- new cell and oven bottom piece (zhiwen)
- The first cell has not been filled due to some complications in the gas system. The second cell is not delivered and won't be until the first one is filled. Alan is working on oven bottom piece.
- temperature optimization test (all)
- Did the Q-curve for water calibration
- Did the sensitivity test of Lock—in and linear magnifying quality of preamplifier， Chunhua will compare measured data （Jie， Chunhua）
- Checked fitting with error estimation, in preparation for notes (Chunhua)
- pulse NMR (all)
- Jie wrote the labview program for DAQ (Jie)
- Diffusion mode measurement (all)
- Made the zapper coil （Chunhua）
- new cell and oven bottom piece (zhiwen)
- Calendar
| timeline | Tasks | To be done by | status |
|---|---|---|---|
| new cell and oven bottom piece | |||
| 9/21-10/5 | receiving and check fitting | all | |
| diffusion mode measurement | |||
| 9/21-10/5 | do the test | all | |
| convection flow study | |||
| 9/21-10/5 | make a zapper coil or a pair of coils to confine field better | Chunhua | |
| 9/21-10/5 | do calibration on old and new RTD. connect RTD readout/control in labview | Jie | |
| temperature optimization test | |||
| 9/21-10/05 | find a removable pick-up coil to do another water calibration for future NMR test | all | |
| 9/21-10/05 | improve analysis, check fitting with error estimation and prepare plots for a note. | Chunhua | |
| pulse NMR | |||
| 9/21-10/05 | pNMR setup and test | Jie | |
| 9/21-10/05 | find or make coil and test it with capacitor matchbox | Chunhua | |
