Difference between revisions of "November 13th 2020"
From Hall A Wiki
(Created page with "*Updates ** HCAL ** Bigbite Shower ** INFN GEM ** UVA GEM ** Hodoscope ** CDet") |
|||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
*Updates | *Updates | ||
** HCAL | ** HCAL | ||
| + | *** cosmics working on right side - checking cabling - still DMA transfer error | ||
| + | *** prescale set to 0 to get all the trigger - was set to 1 so was taking half | ||
| + | *** could try to swap FADC from bottom to top crate | ||
| + | *** try with bus analyzer ? | ||
| + | *** Bryan will check readout list | ||
** Bigbite Shower | ** Bigbite Shower | ||
| + | *** PMTs replaced , starting taking data yesterday - will take data over week-end - and switch to CODA3 maybe Tuesday | ||
** INFN GEM | ** INFN GEM | ||
| + | *** running cosmics on week-end with CODA3 - running stable - replacing cable trays and will retest - no need to power cycle low voltage - 3 M events run | ||
** UVA GEM | ** UVA GEM | ||
| + | *** replaced one MPD which was giving read out errors - need to look at data - no errors seen with new MPD | ||
| + | ** BigBite GEM | ||
| + | *** set of 5 APV for testing in TEDF, crates and modules installed | ||
** Hodoscope | ** Hodoscope | ||
| + | *** Mark gave HV write up, can control HV | ||
| + | *** next set of 16 almost ready | ||
| + | *** will setup TDC after switch to CODA3 | ||
** CDet | ** CDet | ||
| + | ***still debugging few individual channels | ||
| + | *** Update on Wednesday - might need to reboot after - update in mounting /site , update should be done through puppet | ||
| + | ** LHRS | ||
| + | *** getting started with intel CPUs and new TI for LHRS | ||
| + | |||
| + | * GEM DAQ rate limitiation : Ben working on simulation will | ||
| + | |||
| + | |||
| + | *RP VME rack and cable : need space for VXS crate and 1 HV crate and patch panel | ||
| + | |||
| + | *TI Daisy chaining mode for TI : need to test - need pull bundle of fiber TI | ||
| + | |||
| + | *Bigbite Calorimeter trigger : | ||
| + | ** would prefer to use digital as default | ||
| + | ** still keep analog trigger as back up and cross check | ||
| + | ** need develop WAPP trigger | ||
| + | |||
| + | ** analog trigger : need DAC setup for remote threshold control | ||
Latest revision as of 12:44, 13 November 2020
- Updates
- HCAL
- cosmics working on right side - checking cabling - still DMA transfer error
- prescale set to 0 to get all the trigger - was set to 1 so was taking half
- could try to swap FADC from bottom to top crate
- try with bus analyzer ?
- Bryan will check readout list
- Bigbite Shower
- PMTs replaced , starting taking data yesterday - will take data over week-end - and switch to CODA3 maybe Tuesday
- INFN GEM
- running cosmics on week-end with CODA3 - running stable - replacing cable trays and will retest - no need to power cycle low voltage - 3 M events run
- UVA GEM
- replaced one MPD which was giving read out errors - need to look at data - no errors seen with new MPD
- BigBite GEM
- set of 5 APV for testing in TEDF, crates and modules installed
- Hodoscope
- Mark gave HV write up, can control HV
- next set of 16 almost ready
- will setup TDC after switch to CODA3
- CDet
- still debugging few individual channels
- Update on Wednesday - might need to reboot after - update in mounting /site , update should be done through puppet
- LHRS
- getting started with intel CPUs and new TI for LHRS
- HCAL
- GEM DAQ rate limitiation : Ben working on simulation will
- RP VME rack and cable : need space for VXS crate and 1 HV crate and patch panel
- TI Daisy chaining mode for TI : need to test - need pull bundle of fiber TI
- Bigbite Calorimeter trigger :
- would prefer to use digital as default
- still keep analog trigger as back up and cross check
- need develop WAPP trigger
- analog trigger : need DAC setup for remote threshold control
