Difference between revisions of "Gemeel122 log 375"
From Hall A Wiki
| Line 49: | Line 49: | ||
| 407 ||cosmic || Mar 15 2011 || || || 3800V || || Junk | | 407 ||cosmic || Mar 15 2011 || || || 3800V || || Junk | ||
|- | |- | ||
| − | | 408 ||ped || Mar 21 2011 || || || | + | | 408 ||ped || Mar 21 2011 || || || 0V || || Hook up ch2 . Pedestals bad |
|- | |- | ||
| − | | 409 ||ped || Mar 21 2011 || || || | + | | 409 ||ped || Mar 21 2011 || || || 0V || || Junk |
|- | |- | ||
| − | | 410 ||ped || Mar 21 2011 || || || | + | | 410 ||ped || Mar 21 2011 || || || 0V || || Had ch1 cables into ch 2 input. |
| + | |- | ||
| + | | 411 ||ped || Mar 21 2011 || || || 0V || || Put ch1 cable back in proper input. Replace gassiplex card and connector for ch2x | ||
| + | |- | ||
| + | | 412 ||ped || Mar 21 2011 || || || 0V || || Replace gassiplex card and connector for ch1x | ||
|- | |- | ||
|- | |- | ||
|} | |} | ||
Revision as of 14:44, 21 March 2011
| RUN # | Source/Cosmic/Pedestal | Date | Start Time | End Time | HV | # of events | notes |
|---|---|---|---|---|---|---|---|
| 376 | Pedestal | Mar 9 2011 | 11:19:40 | 11:20:30 | 3.8V | 1593 | Chamber 1, problem with Y pedestals |
| 377 | Pedestal | Mar 9 2011 | 3.8V | junk, Do not see Y signals on the scope | |||
| 378 | Pedestal | Mar 9 2011 | 3.8V | junk, try changing board for Y readout. | |||
| 379 | Mar 9 2011 | 3.8V | junk | ||||
| 380 | Mar 10 2011 | 3.8V | junk while fixing problem. Not clear what the fix was. Maybe the connecting cable between gassiplex boards was not connected securely | ||||
| 381 | Mar 10 2011 | 3.8V | junk, low voltage off! | ||||
| 382 | Mar 10 2011 | 3.8V | junk, low voltage off! | ||||
| 383 | Ped | Mar 10 2011 | 3.8V | Good pedestal Chamber 1 | |||
| 384 | Cosmic | Mar 10 2011 | 3.8V | Tried 55Fe source. Not good | |||
| 385 | Cosmic | Mar 10 2011 | 3.8V | 90Sr source, center of chamber 1 | |||
| 386 | Cosmic | Mar 10 2011 | 3.8V | 90Sr source, move around chamber 1 | |||
| 387 | Cosmic | Mar 10 2011 | 15:03 | 3.86V | 90Sr source, move around chamber 1 | ||
| 388 | Ped | Mar 10 2011 | 3.86V | adjusted Ch 3 amplifier DC offset | |||
| 389 | Ped | Mar 10 2011 | 3.86V | Noticed ch 3 Y threshold had a gap | |||
| 390 | Ped | Mar 10 2011 | 0V | Connect up Chamber 2, play with DC offset for Ch 2 | |||
| 391 | Ped | Mar 10 2011 | 0V | Pedestal for Ch 1,2 and 3. Need to study | |||
| 404 | Ped | Mar 11 2011 | Pedestal look bad. [RMS ] [Mean] | ||||
| 406 | Ped | Mar 15 2011 | 0V | Pedestal look ok. RMS is small again,but problem with middle part of Ch1X. Start gas flow. [RMS ] [Mean] | |||
| 407 | cosmic | Mar 15 2011 | 3800V | Junk | |||
| 408 | ped | Mar 21 2011 | 0V | Hook up ch2 . Pedestals bad | |||
| 409 | ped | Mar 21 2011 | 0V | Junk | |||
| 410 | ped | Mar 21 2011 | 0V | Had ch1 cables into ch 2 input. | |||
| 411 | ped | Mar 21 2011 | 0V | Put ch1 cable back in proper input. Replace gassiplex card and connector for ch2x | |||
| 412 | ped | Mar 21 2011 | 0V | Replace gassiplex card and connector for ch1x |
