Difference between revisions of "Saturday, Apr. 9: DAY Shift"
From Hall A Wiki
(New page: Return to List of Daily Run Plans ====Shift Duties==== <!-- * Perform extended ~20 minute Carbon Hole run (only '''once''') --> * Take Production data (see below) * If...) |
|||
Line 3: | Line 3: | ||
====Shift Duties==== | ====Shift Duties==== | ||
<!-- * Perform extended ~20 minute Carbon Hole run (only '''once''') --> | <!-- * Perform extended ~20 minute Carbon Hole run (only '''once''') --> | ||
− | + | * If Beam has been down for longer than 3 hours: | |
− | * If Beam has been down for longer than 3 hours | + | ** Perform [[#Reestablish Beam Procedure|Reestablish Beam Procedure]] |
+ | * Take [[#Carbon Hole and Dummy Target Runs|Solid Target Runs]] | ||
+ | * Take [[#Production Running|Production data]] | ||
+ | |||
+ | ====Reestablish Beam Procedure==== | ||
+ | This procedure is to be run every time we recover from an extended beam down (>3 hours). | ||
+ | * Harp Scans | ||
+ | ** Move target to HOME position (if not already there) (mask target motion!) | ||
+ | ** Turn VDC HV '''OFF''' for both arms. | ||
+ | ** Turn DVCS Calo HV '''OFF''' | ||
+ | ** Ask MCC for Raster '''OFF''' (check that it turns off in the scope) | ||
+ | ** Ask MCC to perform Harp Scans (on IHA1H04A and IHA1H04B) | ||
+ | *** Must have three peaks on each with a resolution of ~200-500 μm | ||
+ | *** Have seen a "shoulder" on the last peak before. May be acceptable if other 2 peaks are fine. | ||
+ | ** Ask MCC to make an ELOG with the results of the Harp Scans | ||
+ | * Beam Centering on Carbon Hole Target | ||
+ | ** Move target to the Carbon Hole position (mask target motion!) | ||
+ | ** Ensure Left-HRS momentum is ~1 GeV/c | ||
+ | ** Set Left-HRS DAQ configuration to [https://hallaweb.jlab.org/wiki/index.php/How_to_HRS_/_DVCS#Changing_from_the_.22DVCS.22_run_type_to_the_.22LHRSnew.22_run_type LeftHRSnew] | ||
+ | *** Set prescales as ps_i = 1 for i = 1-6, and ps=0 for all others | ||
+ | ** Turn VDC HC '''OFF''' for both arms. | ||
+ | ** Turn DVCS Calo HV '''OFF''' | ||
+ | ** Ask MCC for Raster '''ON''' at 2x2 | ||
+ | *** Check that it turns '''on''' in the scope, and check Raster GUI to confirm 2x2 setting | ||
+ | ** Ask MCC for 5 μA beam | ||
+ | *** Run spot_L as explained in the [http://hallaweb.jlab.org/equipment/daq/spot.html detailed instructions] | ||
+ | *** If not centered ask MCC to move beam accordingly (check board for coordinates) | ||
+ | *** Repeat test with different beam position until target is centered. | ||
+ | * Raster Target | ||
+ | ** Start the same settings as carbon hole centering | ||
+ | ** Move to Raster Target (mask target motion!) | ||
+ | ** Ask MCC for 5uA beam with Raster ON (2x2) | ||
+ | ** Check rates and confirm they are consistent with rates seen during HOME position | ||
+ | *** If the rates are low and consistent, then move on to next step | ||
+ | *** If the rates are high, it may indicate the beam has an angle that causes the beam to scrape on an edge of the target | ||
+ | **** Notify the RC | ||
+ | **** Ask MCC to readjust BPM positions until this angle is removed | ||
+ | **** When done, perform another Carbon Hole run just to be sure. | ||
+ | |||
+ | ====Carbon Hole and Dummy Target Runs==== | ||
+ | This is to be performed only '''once''' and may be skipped if already performed in previous shift. | ||
+ | * Take a 20 minute Carbon hole run (after establishing beam) | ||
+ | ** Move target to Carbon Hole position (mask target motion!) | ||
+ | ** Ensure Left-HRS momentum is ~1 GeV/c | ||
+ | ** Set Left-HRS DAQ configuration to [https://hallaweb.jlab.org/wiki/index.php/How_to_HRS_/_DVCS#Changing_from_the_.22DVCS.22_run_type_to_the_.22LHRSnew.22_run_type LeftHRSnew] | ||
+ | *** Set prescales as ps_i = 1 for i = 1-6, and ps=0 for all others | ||
+ | ** Turn the Right-HRS VDC HV '''OFF''' | ||
+ | ** Turn the Left-HRS VDC HV '''ON''' | ||
+ | ** Turn DVCS Calo HC '''OFF''' | ||
+ | ** Ensure Raster '''ON''' at 2x2 | ||
+ | *** Check that it turns '''on''' in the scope, and check Raster GUI to confirm 2x2 setting | ||
+ | ** Ask MCC for 5 μA beam | ||
+ | ** Take ~20 minute run with this setting. | ||
====Production Running==== | ====Production Running==== | ||
Line 64: | Line 116: | ||
|- | |- | ||
|} | |} | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
Latest revision as of 23:41, 8 April 2016
Return to List of Daily Run Plans
Contents
Shift Duties
- If Beam has been down for longer than 3 hours:
- Perform Reestablish Beam Procedure
- Take Solid Target Runs
- Take Production data
Reestablish Beam Procedure
This procedure is to be run every time we recover from an extended beam down (>3 hours).
- Harp Scans
- Move target to HOME position (if not already there) (mask target motion!)
- Turn VDC HV OFF for both arms.
- Turn DVCS Calo HV OFF
- Ask MCC for Raster OFF (check that it turns off in the scope)
- Ask MCC to perform Harp Scans (on IHA1H04A and IHA1H04B)
- Must have three peaks on each with a resolution of ~200-500 μm
- Have seen a "shoulder" on the last peak before. May be acceptable if other 2 peaks are fine.
- Ask MCC to make an ELOG with the results of the Harp Scans
- Beam Centering on Carbon Hole Target
- Move target to the Carbon Hole position (mask target motion!)
- Ensure Left-HRS momentum is ~1 GeV/c
- Set Left-HRS DAQ configuration to LeftHRSnew
- Set prescales as ps_i = 1 for i = 1-6, and ps=0 for all others
- Turn VDC HC OFF for both arms.
- Turn DVCS Calo HV OFF
- Ask MCC for Raster ON at 2x2
- Check that it turns on in the scope, and check Raster GUI to confirm 2x2 setting
- Ask MCC for 5 μA beam
- Run spot_L as explained in the detailed instructions
- If not centered ask MCC to move beam accordingly (check board for coordinates)
- Repeat test with different beam position until target is centered.
- Raster Target
- Start the same settings as carbon hole centering
- Move to Raster Target (mask target motion!)
- Ask MCC for 5uA beam with Raster ON (2x2)
- Check rates and confirm they are consistent with rates seen during HOME position
- If the rates are low and consistent, then move on to next step
- If the rates are high, it may indicate the beam has an angle that causes the beam to scrape on an edge of the target
- Notify the RC
- Ask MCC to readjust BPM positions until this angle is removed
- When done, perform another Carbon Hole run just to be sure.
Carbon Hole and Dummy Target Runs
This is to be performed only once and may be skipped if already performed in previous shift.
- Take a 20 minute Carbon hole run (after establishing beam)
- Move target to Carbon Hole position (mask target motion!)
- Ensure Left-HRS momentum is ~1 GeV/c
- Set Left-HRS DAQ configuration to LeftHRSnew
- Set prescales as ps_i = 1 for i = 1-6, and ps=0 for all others
- Turn the Right-HRS VDC HV OFF
- Turn the Left-HRS VDC HV ON
- Turn DVCS Calo HC OFF
- Ensure Raster ON at 2x2
- Check that it turns on in the scope, and check Raster GUI to confirm 2x2 setting
- Ask MCC for 5 μA beam
- Take ~20 minute run with this setting.
Production Running
For the remainder of the shift take 1 hour runs in the production configuration DVCS: Kin_48_2
Beam current | 15 μA |
Target | LH2 |
Raster | ON (2x2mm2) |
VDC HV (both arms) | ON |
DVCS Calo HV | ON |
DVCS Calo Angle; | 15.185° |
DVCS Calo Distance | 2.0 m |
LHRS Polarity | Negative |
LHRS Momentum | 3.996 GeV/c |
LHRS Angle | 20.243° |
LHRS Q1 Current | 1916.640 (regulator OFF) |
LHRS DAQ Config | DVCS |
prescaleL | PS9=1 (all others zero) |
RHRS Polarity | Negative |
RHRS Momentum | 2.101 GeV/c |
RHRS Angle | 48.892° |
RHRS DAQ Config | RHRSadaq2 |
prescaleR | PS1=PS2=PS3=1, && PS8=200 (all others zero) |