Difference between revisions of "Target Field and Kepco Power Supplies"
From Hall A Wiki
(→Plan for returning from CODIV shutdown) |
|||
| (3 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | This page is dedicated to all things | + | This page is dedicated to all things Target Field related |
| − | + | ==Log Entries== | |
** Nov. 26th Kepcos replaced Agilents https://logbooks.jlab.org/entry/3744320 | ** Nov. 26th Kepcos replaced Agilents https://logbooks.jlab.org/entry/3744320 | ||
** Dec. 26th V_in vs Current Calibration for two Kepcos in voltage control mode https://logbooks.jlab.org/entry/3747508 | ** Dec. 26th V_in vs Current Calibration for two Kepcos in voltage control mode https://logbooks.jlab.org/entry/3747508 | ||
| Line 13: | Line 13: | ||
** March 22nd Odd behavior explained from above. Noticed possible grounding issues. https://logbooks.jlab.org/entry/3807894 | ** March 22nd Odd behavior explained from above. Noticed possible grounding issues. https://logbooks.jlab.org/entry/3807894 | ||
** March 24th Trouble getting transverse NMR signal. Bad Cable? https://logbooks.jlab.org/entry/3809148 | ** March 24th Trouble getting transverse NMR signal. Bad Cable? https://logbooks.jlab.org/entry/3809148 | ||
| + | |||
| + | ==Coil Currents for D2n== | ||
| + | |||
| + | ==Labview Program Guide== | ||
| + | |||
| + | ==Field Measurements== | ||
| + | |||
| + | ==Plan for returning from CODIV shutdown== | ||
| + | ** Follow manufactureres "Check out" procedure for new power supply which was delivered during shutdown | ||
| + | ** Measure resistance to ground for both coils | ||
| + | ** Install latest new power supply, add additional circuitry | ||
| + | ** Test power supplies in both current and voltage control mode | ||
| + | ** Look at PS output on scope, with and without RF on. | ||
| + | ** Test NMR in both voltage and current mode | ||
| + | ** Ensure Labview is ready to go for either configuration | ||
Latest revision as of 10:34, 1 June 2020
This page is dedicated to all things Target Field related
Contents
Log Entries
- Nov. 26th Kepcos replaced Agilents https://logbooks.jlab.org/entry/3744320
- Dec. 26th V_in vs Current Calibration for two Kepcos in voltage control mode https://logbooks.jlab.org/entry/3747508
- Jan. 4th Swapped out Kepco with another Kepco because it was not stable https://logbooks.jlab.org/entry/3758511
- Jan. 15th Swapped out Kepco with another Kepco because it was running hot and tripping https://logbooks.jlab.org/entry/3764365
- Feb. 9th Field sweep program updated for Agilent https://logbooks.jlab.org/entry/3780264
- Feb. 10th Replaced Kepco with Agilent. Rearranged rack for better cooling https://logbooks.jlab.org/entry/3781492
- Feb. 14th Replaced Agilent with new Kepco. In constant current mode the inductive load option interfered with NMR https://logbooks.jlab.org/entry/3783977
- March 18th In constant voltage mode, coils need time to warm up https://logbooks.jlab.org/entry/3805990
- March 22nd New kepco had odd behavior in voltage mode. Transverse NMR was not working. Left in current mode. https://logbooks.jlab.org/entry/3807357
- March 22nd Odd behavior explained from above. Noticed possible grounding issues. https://logbooks.jlab.org/entry/3807894
- March 24th Trouble getting transverse NMR signal. Bad Cable? https://logbooks.jlab.org/entry/3809148
Coil Currents for D2n
Labview Program Guide
Field Measurements
Plan for returning from CODIV shutdown
- Follow manufactureres "Check out" procedure for new power supply which was delivered during shutdown
- Measure resistance to ground for both coils
- Install latest new power supply, add additional circuitry
- Test power supplies in both current and voltage control mode
- Look at PS output on scope, with and without RF on.
- Test NMR in both voltage and current mode
- Ensure Labview is ready to go for either configuration
