Difference between revisions of "G2p Remote Crate Resets"
From Hall A Wiki
(→Remote Crate Resets) |
|||
| Line 5: | Line 5: | ||
=====ROC1/ROC2/ROC6===== | =====ROC1/ROC2/ROC6===== | ||
| − | * | + | * Type "reboot" in the portserver terminal window. |
| + | * If doing above doesn't help then go to HALL-A tools screen on hacsbc2 (left-hand side of shift leader's computer) | ||
* Under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Electron Detector Stack (right) Crate" look for "SFI (Fastbus ROC1 and ROC2) #1" and click on "click to reset" button. After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run. | * Under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Electron Detector Stack (right) Crate" look for "SFI (Fastbus ROC1 and ROC2) #1" and click on "click to reset" button. After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run. | ||
* If doing above doesn't help, then under "Resets from the Electron Detector Stack (right) Crate" look for "Lower Fastbus AC" and click on "click to reset" button.For ROC1,the boot parameters will need to be re-entered in the portserver terminal window, check the "special note for ROC1/ROC3" in this document below [[https://hallaweb.jlab.org/wiki/index.php/G2p_Remote_Crate_Resets#Special_Note_on_ROC3.2FROC1 Special_Note_on_ROC1/ROC3]]. | * If doing above doesn't help, then under "Resets from the Electron Detector Stack (right) Crate" look for "Lower Fastbus AC" and click on "click to reset" button.For ROC1,the boot parameters will need to be re-entered in the portserver terminal window, check the "special note for ROC1/ROC3" in this document below [[https://hallaweb.jlab.org/wiki/index.php/G2p_Remote_Crate_Resets#Special_Note_on_ROC3.2FROC1 Special_Note_on_ROC1/ROC3]]. | ||
| Line 11: | Line 12: | ||
=====TS0===== | =====TS0===== | ||
| − | * | + | * Type "reboot" in the portserver terminal window. |
| + | * If doing above doesn't help then go to HALL-A tools screen on hacsbc2 (left-hand side of shift leader's computer) | ||
* Under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Electron Detector Stack (right) Crate" look for "Trigger Supervisor" and click on "click to reset" button. | * Under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Electron Detector Stack (right) Crate" look for "Trigger Supervisor" and click on "click to reset" button. | ||
* After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run. | * After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run. | ||
| Line 17: | Line 19: | ||
=====ROC26===== | =====ROC26===== | ||
| − | * | + | * Type "reboot" in the portserver terminal window. |
| + | * If doing above doesn't help then direct a webbrowser to [http://hareboot32 hareboot32], the password is written on the "Passwords" sheet near the white board. Click "Control Action" perform and select "Immediate Reboot" for Outlet 8 "happex7 RHRS(ROC 26)", then click "apply". | ||
* After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run. | * After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run. | ||
=====ROC3/ROC4/ROC5===== | =====ROC3/ROC4/ROC5===== | ||
| − | * | + | * Type "reboot" in the portserver terminal window. |
| + | * If doing above doesn't help then go to HALL-A tools screen on hacsbc2 (left-hand side of shift leader's computer) | ||
* Under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Hadron Detector Stack (left) Crate" look for "SFI (Fastbus ROC3 & ROC4) #1" and click on "click to reset" button. After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run. | * Under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Hadron Detector Stack (left) Crate" look for "SFI (Fastbus ROC3 & ROC4) #1" and click on "click to reset" button. After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run. | ||
* If doing all above doesn't help then under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Hadron Detector Stack (left) Crate" look for "Lower Fastbus AC" and click on "click to reset" button. For ROC3,the boot parameters will need to be re-entered in the portserver terminal window, check the "special note for ROC1/ROC3" in this document below [[https://hallaweb.jlab.org/wiki/index.php/G2p_Remote_Crate_Resets#Special_Note_on_ROC3.2FROC1 Special Note for ROC1/ROC3]]. | * If doing all above doesn't help then under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Hadron Detector Stack (left) Crate" look for "Lower Fastbus AC" and click on "click to reset" button. For ROC3,the boot parameters will need to be re-entered in the portserver terminal window, check the "special note for ROC1/ROC3" in this document below [[https://hallaweb.jlab.org/wiki/index.php/G2p_Remote_Crate_Resets#Special_Note_on_ROC3.2FROC1 Special Note for ROC1/ROC3]]. | ||
| Line 28: | Line 32: | ||
=====TS11===== | =====TS11===== | ||
| − | * | + | * Type "reboot" in the portserver terminal window. |
| + | * If doing above doesn't help then go to HALL-A tools screen on hacsbc2 (left-hand side of shift leader's computer) | ||
* Under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Hadron Detector Stack (left) Crate" look for "Trigger Supervisor" and click on "click to reset" button. | * Under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Hadron Detector Stack (left) Crate" look for "Trigger Supervisor" and click on "click to reset" button. | ||
* After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run. | * After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run. | ||
| Line 34: | Line 39: | ||
=====ROC 25===== | =====ROC 25===== | ||
| − | * | + | * Type "reboot" in the portserver terminal window. |
| + | * If doing above doesn't help then direct a webbrowser to [http://hareboot28 hareboot28],the password is written on the "Passwords" sheet near the white board. Click "Control Action" perform and select "Immediate Reboot" for Outlet 1 "happex8 LHRS(ROC 25)", then click "apply". | ||
* After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run. | * After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run. | ||
Revision as of 14:17, 1 March 2012
Contents
Remote Crate Resets
The following is how to remotely reset the crates when the crates get hung up, and cannot be rebooted.
ROC1/ROC2/ROC6
- Type "reboot" in the portserver terminal window.
- If doing above doesn't help then go to HALL-A tools screen on hacsbc2 (left-hand side of shift leader's computer)
- Under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Electron Detector Stack (right) Crate" look for "SFI (Fastbus ROC1 and ROC2) #1" and click on "click to reset" button. After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run.
- If doing above doesn't help, then under "Resets from the Electron Detector Stack (right) Crate" look for "Lower Fastbus AC" and click on "click to reset" button.For ROC1,the boot parameters will need to be re-entered in the portserver terminal window, check the "special note for ROC1/ROC3" in this document below [Special_Note_on_ROC1/ROC3].
TS0
- Type "reboot" in the portserver terminal window.
- If doing above doesn't help then go to HALL-A tools screen on hacsbc2 (left-hand side of shift leader's computer)
- Under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Electron Detector Stack (right) Crate" look for "Trigger Supervisor" and click on "click to reset" button.
- After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run.
ROC26
- Type "reboot" in the portserver terminal window.
- If doing above doesn't help then direct a webbrowser to hareboot32, the password is written on the "Passwords" sheet near the white board. Click "Control Action" perform and select "Immediate Reboot" for Outlet 8 "happex7 RHRS(ROC 26)", then click "apply".
- After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run.
ROC3/ROC4/ROC5
- Type "reboot" in the portserver terminal window.
- If doing above doesn't help then go to HALL-A tools screen on hacsbc2 (left-hand side of shift leader's computer)
- Under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Hadron Detector Stack (left) Crate" look for "SFI (Fastbus ROC3 & ROC4) #1" and click on "click to reset" button. After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run.
- If doing all above doesn't help then under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Hadron Detector Stack (left) Crate" look for "Lower Fastbus AC" and click on "click to reset" button. For ROC3,the boot parameters will need to be re-entered in the portserver terminal window, check the "special note for ROC1/ROC3" in this document below [Special Note for ROC1/ROC3].
TS11
- Type "reboot" in the portserver terminal window.
- If doing above doesn't help then go to HALL-A tools screen on hacsbc2 (left-hand side of shift leader's computer)
- Under "MISCELLANEOUS" section click on "Crate Resets" and under "Resets from the Hadron Detector Stack (left) Crate" look for "Trigger Supervisor" and click on "click to reset" button.
- After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run.
ROC 25
- Type "reboot" in the portserver terminal window.
- If doing above doesn't help then direct a webbrowser to hareboot28,the password is written on the "Passwords" sheet near the white board. Click "Control Action" perform and select "Immediate Reboot" for Outlet 1 "happex8 LHRS(ROC 25)", then click "apply".
- After rebooting, in the runcontrol GUI, click Abort, click Reset, click Download, and then start a run.
Special Note on ROC3/ROC1
- If the LHRS (RHRS) crate is power cycled, the boot parameters for ROC3(ROC1) will need to be re-entered. The boot parameters are located in doc/vmeram g2p.doc and also on the g2p Wiki[Boot_Parameters_for_g2p]. To change the boot parameters do the following:
- Go to the vxWorks prompt for ROC3 and type ”c”.
- This will allow you to enter the parameters, one line at a time.
- When finished, type ”p” to print the boot parameters (and check that they are correct)
- Type ”@” to reboot the ROC.
