|
|
| Line 8: |
Line 8: |
| | [[http://edwards1.phy.ohiou.edu/~roche/transfer/DVCS_TRIGER_version_2014_24_9_2013%20copy.pdf Trigger Manual (Sept 2013)]] | | [[http://edwards1.phy.ohiou.edu/~roche/transfer/DVCS_TRIGER_version_2014_24_9_2013%20copy.pdf Trigger Manual (Sept 2013)]] |
| | [[http://edwards1.phy.ohiou.edu/~roche/transfer/dvcs_march11/Status%20and%20upgrades_copyII.pdf Trigger upgrade talk (March 2011)]] | | [[http://edwards1.phy.ohiou.edu/~roche/transfer/dvcs_march11/Status%20and%20upgrades_copyII.pdf Trigger upgrade talk (March 2011)]] |
| − |
| |
| − |
| |
| − |
| |
| − |
| |
| − | === Tips (known work around) ===
| |
| − | This article is being created to outline various issues that have been done while working on the DVCS Trigger and DAQ. The aim is to describe step-by-step how various issues were resolved. This is mainly to serve as a future reference should issues similar to these arise again later.
| |
| − |
| |
| − | Major issues are listed as follows:
| |
| − |
| |
| − | 1. Trigger losing firmware data: causing all channels to give the same output ([https://hallaweb.jlab.org/dvcslog/NewDAQ/237| see ELOG]) for most (or all) events.
| |
| − |
| |
| − | 2. Transfer CODA configurations from adaql2 (the old machine) to adaq1 (the new machine).
| |
| − |
| |
| − | ==== Issue 1: Losing Firmware data ====
| |
| − |
| |
| − | Download firmware data again. In order to do this, you must have a working version of Quartus II on a laptop. Check if your laptop is a 32-bit system or 64-bit system. If the laptop is a 64-bit system, do the following (in this order unless stated otherwise):
| |
| − |
| |
| − | 1. Download or check that you have the 32-bit version of the following libraries for your OS (if you already have a 32-bit system, then you can skip this step):
| |
| − |
| |
| − | *glibc
| |
| − |
| |
| − | *libxext
| |
| − |
| |
| − | *libx11
| |
| − |
| |
| − | *libxau
| |
| − |
| |
| − | *libxdmcp
| |
| − |
| |
| − | *freetype
| |
| − |
| |
| − | *fontconfig
| |
| − |
| |
| − | *expat
| |
| − |
| |
| − | 2. Download the latest version of Quartus II ([http://dl.altera.com/?edition=web| Here]) .
| |
| − |
| |
| − | 3. Install Quartus II (the installer can be found in the '''bin''' folder) by running the appropriate script.
| |
| − |
| |
| − | 4. Check that the USB Blaster is working by plugging it into the computer and running quartus. Then in the menu do '''Tools->Programmer->Hardware Setup'''. You should see the blaster in available hardware items. This means that you are ready to go.
| |
Revision as of 12:19, 20 October 2014
Back to DVCS3
This page as it stand here, is very much out of date.
Documentation
[Trigger Manual (Sept 2013)]
[Trigger upgrade talk (March 2011)]
