Difference between revisions of "Happex compton"
From Hall A Wiki
(→Old Compton Table) |
(→Compton Table, Spring 2016) |
||
| Line 6: | Line 6: | ||
Find JTabs on compton@compton: | Find JTabs on compton@compton: | ||
| − | # | + | # In compton@compton: type ''NewTools'' from the home directory. Pulls up a small OPS menu. |
| − | # Click on it. Go to EDM Hall A. | + | # Click on it. Go to EDM Hall A. Find JTabs Hall A. |
| − | # Start JTabs. | + | # Start JTabs. Go to Hall A --> Compton --> Controls --> brings up an EDM window. You want the calorimeter table. |
| − | |||
<strong> Note: the vertical max is 39.99 mm!! The nominal X, Y: 69.9mm, 24.4mm. </strong> | <strong> Note: the vertical max is 39.99 mm!! The nominal X, Y: 69.9mm, 24.4mm. </strong> | ||
| + | |||
===Helicity controls:=== | ===Helicity controls:=== | ||
| − | # On far right of JTabs menu, there are "master" controls. | + | # On far right of JTabs menu, there are "master" controls. Find and click on Tools Screen. |
# Go to the helicity controls. (The default is delayed, so be careful of this.) | # Go to the helicity controls. (The default is delayed, so be careful of this.) | ||
| Line 21: | Line 21: | ||
===Trouble shooting:=== | ===Trouble shooting:=== | ||
| − | The lockout position is the same as the home position (poor design). | + | The lockout position is the same as the home position (poor design). |
To jog it by hand away from the home position: | To jog it by hand away from the home position: | ||
| − | # Open up the floor tile against the wall next to the Compton computer. You want the remote | + | # Open up the floor tile against the wall next to the Compton computer. You want the remote control: it is a small beige box with controls. (other box is a killswitch; do not touch). |
| − | # You need to first activate the box (turn it on: bottom right switch), or it won't do anything. The red light may or may not come on when you do this (LED is dying). Depending on whether the shift is activated or not, some buttons do two things. You need to toggle the table up just barely. So, flick the switch up, then flip it right back down. Now the JTabs controls should be working. Make sure to switch the box back off when you are finished. | + | # You need to first activate the box (turn it on: bottom right switch), or it won't do anything. The red light may or may not come on when you do this (LED is dying). Depending on whether the shift is activated or not, some buttons do two things. You need to toggle the table up just barely. So, flick the switch up, then flip it right back down. Now the JTabs controls should be working. |
| − | + | # Make sure to switch the box back off when you are finished, and replace carefully. | |
| − | + | ||
==Old Compton Table, pre-Spring 2016== | ==Old Compton Table, pre-Spring 2016== | ||
In the case of an epics reboot, the Compton photon detector table moves to the home position. This is a problem, since this is not the nominal position. The table must then be moved back to the nominal position. To do this, you must first move the table to home using the controller box located int he back room of the Counting House. Then you must move it up (vertical up) a little from home using the controller. If you don't know where this is or how to use it, page Megan. You can then open up the Compton table GUI and move the table to x=70.3 and y=43.0 (since the table appears to have sunk a little, the old position was 41.3). The crystal should now be in the nominal position. <strong>WARNING: Do not move the table above y=44mm! The lead hut will hit the electron detector table!</strong> | In the case of an epics reboot, the Compton photon detector table moves to the home position. This is a problem, since this is not the nominal position. The table must then be moved back to the nominal position. To do this, you must first move the table to home using the controller box located int he back room of the Counting House. Then you must move it up (vertical up) a little from home using the controller. If you don't know where this is or how to use it, page Megan. You can then open up the Compton table GUI and move the table to x=70.3 and y=43.0 (since the table appears to have sunk a little, the old position was 41.3). The crystal should now be in the nominal position. <strong>WARNING: Do not move the table above y=44mm! The lead hut will hit the electron detector table!</strong> | ||
Revision as of 12:12, 29 January 2016
The main compton page is here, this page just highlights the new stuff.
Contents
Compton Table, Spring 2016
Compton GUI:
Find JTabs on compton@compton:
- In compton@compton: type NewTools from the home directory. Pulls up a small OPS menu.
- Click on it. Go to EDM Hall A. Find JTabs Hall A.
- Start JTabs. Go to Hall A --> Compton --> Controls --> brings up an EDM window. You want the calorimeter table.
Note: the vertical max is 39.99 mm!! The nominal X, Y: 69.9mm, 24.4mm.
Helicity controls:
- On far right of JTabs menu, there are "master" controls. Find and click on Tools Screen.
- Go to the helicity controls. (The default is delayed, so be careful of this.)
Trouble shooting:
The lockout position is the same as the home position (poor design).
To jog it by hand away from the home position:
- Open up the floor tile against the wall next to the Compton computer. You want the remote control: it is a small beige box with controls. (other box is a killswitch; do not touch).
- You need to first activate the box (turn it on: bottom right switch), or it won't do anything. The red light may or may not come on when you do this (LED is dying). Depending on whether the shift is activated or not, some buttons do two things. You need to toggle the table up just barely. So, flick the switch up, then flip it right back down. Now the JTabs controls should be working.
- Make sure to switch the box back off when you are finished, and replace carefully.
Old Compton Table, pre-Spring 2016
In the case of an epics reboot, the Compton photon detector table moves to the home position. This is a problem, since this is not the nominal position. The table must then be moved back to the nominal position. To do this, you must first move the table to home using the controller box located int he back room of the Counting House. Then you must move it up (vertical up) a little from home using the controller. If you don't know where this is or how to use it, page Megan. You can then open up the Compton table GUI and move the table to x=70.3 and y=43.0 (since the table appears to have sunk a little, the old position was 41.3). The crystal should now be in the nominal position. WARNING: Do not move the table above y=44mm! The lead hut will hit the electron detector table!
