Difference between revisions of "Tuesday, Mar. 08: DAY Shift"
From Hall A Wiki
(New page: Go back to Daily Run Plan Daily Run Plans <b>Previously...</b> * Production data (Kin48_3) <b>Specific mission</b> *** <b>Elastic measurement during DAY</b> * 6:30AM Call MCC fo...) |
|||
| Line 10: | Line 10: | ||
<b>Specific mission</b> | <b>Specific mission</b> | ||
*** <b>Elastic measurement during DAY</b> | *** <b>Elastic measurement during DAY</b> | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| + | - 6:30 am: | ||
| + | Beam Off, Call MCC to put Hall A in Controlled Access | ||
| + | Starting Ramping HRS-L magnets to 0 | ||
| + | - 7:30 am: | ||
| + | Tech in Hall, Change HRS-L Polarity, Move Angle to 40.0 deg, Set Momentum = 2.5106 GeV/c, Q1 = 1900 Amp | ||
| + | - 8:30 am: | ||
| + | Elastic Angle Calibration: | ||
| + | DVCS Trigger s0 only in HRS trigger, Elastics with Calo in current Kin_048_3 setting 15 microAmp | ||
| + | - 9:30 am Escorted Access | ||
| + | Move Calo to 6 m, 14.0 deg | ||
| + | - 10:00 Elastic Energy Calibration data 20 microAmp | ||
| + | - 10:30 Escorted Access, Move Calo to 13.1 deg | ||
| + | - 11:00 Elastic Energy Calibration data | ||
| + | - 11:30 Escorted Access: Move Calo to 12.25 deg | ||
| + | - 12:00 Elastic Energy Calibration data | ||
| + | - 12:30 Move Calo to Kin_48_2 setting: 15.184 deg, D=2.0 m, 10 micro Amp | ||
| + | - 13:00 Angle Calibration Data | ||
| + | (This puts the central elastic 7.1 GeV electrons 2.0 blocks from the physical edge of the calorimeter.) | ||
| + | - 14:00 Controlled Access? | ||
| + | Ramp down HRS-L | ||
| + | Polarity, Angle change HRS-L to 20.244 deg to p = -3.996 GeV/c, Q1 = 1900 Amp | ||
| + | - 15:00 Production DVCS at KIN_48_2 | ||
Revision as of 19:08, 7 March 2016
Go back to Daily Run Plan Daily Run Plans
Previously...
- Production data (Kin48_3)
Specific mission
- Elastic measurement during DAY
- 6:30 am:
Beam Off, Call MCC to put Hall A in Controlled Access
Starting Ramping HRS-L magnets to 0
- 7:30 am:
Tech in Hall, Change HRS-L Polarity, Move Angle to 40.0 deg, Set Momentum = 2.5106 GeV/c, Q1 = 1900 Amp
- 8:30 am:
Elastic Angle Calibration:
DVCS Trigger s0 only in HRS trigger, Elastics with Calo in current Kin_048_3 setting 15 microAmp
- 9:30 am Escorted Access
Move Calo to 6 m, 14.0 deg
- 10:00 Elastic Energy Calibration data 20 microAmp
- 10:30 Escorted Access, Move Calo to 13.1 deg
- 11:00 Elastic Energy Calibration data
- 11:30 Escorted Access: Move Calo to 12.25 deg
- 12:00 Elastic Energy Calibration data
- 12:30 Move Calo to Kin_48_2 setting: 15.184 deg, D=2.0 m, 10 micro Amp
- 13:00 Angle Calibration Data
(This puts the central elastic 7.1 GeV electrons 2.0 blocks from the physical edge of the calorimeter.)
- 14:00 Controlled Access?
Ramp down HRS-L
Polarity, Angle change HRS-L to 20.244 deg to p = -3.996 GeV/c, Q1 = 1900 Amp
- 15:00 Production DVCS at KIN_48_2
- Back to Production run, Kin48_2
- After Alex's work, Compton laser will be turned OFF !
- Polarized beam at 15 uA on LH2 15 cm! (out of chicane ? )
- DVCS is running kin_48_2 [here]
- LHRS is partially detuned: [here]
- LHRS=3.996GeV, Q1/Q2/Q3=1916.640(readout:1900)/1600/1600 (Q1 regul.OFF)
- PreScaleR : PS1=PS2=PS3=1, && PS8=200
- PreScaleL : PS9 =1, + DVCS config.
- beam locks: no position lock, energy lock in Arc 2: [here]
- DVCS daq configuration is [this one], we are measuring about 2% DT at 15uA.
BPM/Spot++ Check
- After beam lost for considerable time (like beam study, pass change,...)
- Ask MCC to run 5uA wth carbon hole target and make sure you can see the hole through Spot++
Please check more info on the white board in the Counting House ~!!
