Difference between revisions of "VDC HV control"

Revision as of 15:09, 6 April 2017

Relay Box with 8 relays (channels) controlled by RPi board is used to limit trip current and prevent trips for VDC high voltage line during HV on/off operation.

Two of them have been installed in Left and Right HRS at the end of March, 2017.

• Left HRS:

  name: rpileft 
  IP: 129.57.164.27
  passwd: same as for rpi8

• Right HRS:

  name: rpiright 
  IP: 129.57.164.53
  passwd: same as for rpi7

Relay box consists of 8 relays and 8 resistors with 68Mohm nominal. Resistor is connected in series between output of hv channel and VDC hv line, or shortened by relay (diagram view).

RPi board is used as TCP/IP server to control relays by commands from clients. RPi board in HV crate (rpi8(left), rpi7(right)) runs 'shim-server' to control modules in crate.

Shim-server will send commands to relay box server to switch relay ON (closed, shortened resistor) or OFF (open, resistor in).

Shim-server checks commands/responses from GUI to hv channel that connected to VDC. The next logic is used by shim-server to control relays :

• commands: HVON, HVOFF, demand voltage (DV) set, enable/disable channel (CE), channels status (ST>1) ---> relay is OFF (open, resistor in) for this channel.
• channel status ST==1 --> relay is ON (closed, resistor out) for this channel.
• initial state of relay set by RPi board after power on is all relays OFF (open, resistor in).

Command format for relay box server is the same as used by LeCroy HV system (examples):

• set relay channel #1 to ON (closed)

LD S0.1 RLY 1

• set relay channels #0,#2 to ON (closed) and channels #1,#3-#7 to OFF (open)

LD S0 RLY 1 0 1 0 0 0 0 0

• get status of all relays channel (1 - is ON, 0 - is OFF)

RC S0 RLY
replay:     1 RC S0 RLY 1 0 1 0 0 0 0 0

Hv module for VDC will have one more property column 'RLY_en' in Java GUI, that shows status of relay box channels (0 - relay is OFF, 1 - relay is ON).

Configuration file for relay server

Configuration file is needed to activate relay controls from 'shim-server' on rpi7 or rpi8. Shim-server reads parameters from this file when it started.

There is configuration file /home/pi/relay.config with relay server parameters on rpi7:

# Parameters of relay server.
# Host name of relay server:               host=<IP/name_of_relay_server>
# Connection Port of relay server:         port=1090
# Slot with HV module connected to VDC:    slot=S<number>
# HV module channel map to relay channels: chmap=<HV_channel>.<relay_channel>
host=rpiright
port=1090
slot=S12
chmap=0.0 1.2 2.1 3.3 4.4 5.5 6.6 7.7

There is configuration file /home/pi/relay.config with relay server parameters on rpi8:

# Parameters of relay server.
# Host name of relay server:               host=<IP/name_of_relay_server>
# Connection Port of relay server:         port=1090
# Slot with HV module connected to VDC:    slot=S<number>
# HV module channel map to relay channels: chmap=<HV_channel>.<relay_channel>
host=rpileft
port=1090
slot=S7
chmap=0.0 1.3 2.2 3.1 4.4 5.5 6.6 7.7

Software update on rpi7 and rpi8

• shim-server for VDC relays control: /home/pi/tcp_test/LecroyHV_Shim_tcp_VDC
• script to start hv servers: /home/pi/scripts/start_hv

#!/bin/bash
# Starts HV servers on Rasapberry Pi
#
# start HV1458 server (port=24742)
sudo ~/tcp_test/20140803_i2lchv_rPI-linux &
# wait while HV1458 initialized
sleep 2
# start Perl shim server (port=2001)
##~/tcp_test/LecroyHV_Shim_tcp2
~/tcp_test/LecroyHV_Shim_tcp_VDC

HV Relay Box

• Schematic diagram of relay box (drivers type of NCV8403 between D-25 control connector and relays not shown): HV Relay Box.pdf

• Inside picture:

25-Dsub connector is an input with the following pinout:

--------------------------------------------------------
\  1   2   3   4   5   6   7   8   9   10  11  12  13  / 
 \ 14  15  16  17  18  19  20  21  22   23  24  25    /
  ----------------------------------------------------
(1) Relay 1 - +3.3vdc logic from rPi
(2) Relay 2 - ""
(3) Relay 3 - ""
(4) Relay 4 - ""
(5) Relay 5 - ""
(6) Relay 6 - ""
(7) Relay 7 - ""
(8) Relay 8 - ""
(9) Not used
(10) Not used
(11) Not used
(12) Not used
(13) Not used
(14 -21) rPi common[GND]
(22) Not used
(23) Not used
(24) Not used
(25) Not used

RPi board GPIO 26-pin connector to relay box (logic 1 - relay is ON, logic 0 - relay is OFF):

RPi
Pins#   Wire Name
6       Ground (0V)
7       relay ch#1
11      relay ch#2
12      relay ch#3
13      relay ch#4
15      relay ch#5
16      relay ch#6
18      relay ch#7
22      relay ch#8