G2p Analysis Minutes
Minutes of the weekly analysis meetings
8/10/2011: Present: Kalyan, Jixie, Chao, Pengjia, Mellisa, Vincent, Ryan, Toby, Alexandre, Jie Liu
7/27/2011: Present: Kalyan, Jixie, Chao, Pengjia, Mellisa, Vincent, Ryan, Toby, Alexandre, Jie Liu
www.jlab.org/~jixie/meeting/20091216_NewBeamE/real_raw_oldE/pcorr_level1/Gr5/MM3_5G_PNB.gif
7/20/2011: Present:Karl, Jixie, Chao, Pengjia, Mellisa, Vincent, Ryan, Toby, Alexandre, Jie Liu
- Jixie:
1) The design of the 3rd arm:
A) [Figure http://www.jlab.org/~jixie/HallA/meeting/20110720_ThirdArm/ThetaAcc_R1B2G5.png]
shows the hit positions on the SC plane. The distribution look like a rotated strip.
In order to select a small range of theta, the SC need to be rotated to some angle such that only the
7/13/2011: Present:Jian-ping, Jixie, Chao, Pengjia, Mellisa, Vincent, Ryan, Toby, Alexandre, Jie Liu, Karl
- Mellisa:
1) Continue checking the Cherencov detector. Applied geometry cut to the ADC. She need to find out
the ADC value that 1 PHE corresponding to. Check her plots in the Elog, Item 120:
https://hallaweb.jlab.org/dvcslog/g2p/120
- Toby:
1) Showed the preliminary result for the field map analysis with the can surface data set. Most data
points are within 6% variation. But the position offsets are as large as 2 cm.
- Jie:
1) Showed his result of the field map analysis. Most data points are with 10% variation to the
TOSCA map. Jie's result does not agree with Toby's in position and current ratio. Both of them are
requested to check their results more carefully.
- Pengjia:
1) Tried to build ring buffer in HAPPEX DAQ. Will do the tungsten calorimeter calibration in August.
- Ryan:
1)Looked into the HV for HRS
2)Finish the splitter box.
- Chao:
1) Tried to learn and run the Geant4 simulation for the 3rd arm.
- Jixie:
1) Looking into the neutron background data provided by Pavel. 2) Designing the 3rd arm.
7/6/2011: Present: Jian-ping, Kalyan, Jixie, Chao, Pengjia, Mellisa, Vincent, Ryan, Toby, Alexandre, Jie Liu
- JP:
1) Discussed the run plan with QWEAK group, ask for 12 days for 1.7 GeV. Not be granted yet.
Currently Hall C allow only 5 days, or If they are down then we can take the time for 1.7 GeV.
The plan is still under discussion.
2) If Hall B is not available, we need to be able to run 1.2 GeV. We should be very flexible and
ready for changes.
3) Karl has the readiness review available. Everyone is encouraged to read and comment.
4) JP will leave from 7/22 to 8/17. Kaylan will leave to India from 7/8 to 7/29.
Alex will on vacation from 7/23 to 8/11. Karl will be on site from 7/11.
- Min:
1) Just back from the summer school. Will continue working on the HRS package issues.
- Chao:
1) Taking the detector geometry into account, recalculated the background of the 3rd arm using the epc code.
2) Discuss the 3rd arm design: 12 inch width will accept +/-4 degrees in theta. With such a wide
range it will take about 16 hours to measure Pb*Pt to 5% accuracy. It is too long ...
3) Finish the target field measurement with Jixie and Toby.
- Pengjia:
1)Leaning HAPPEX DAQ, will use it for BCM and BPM
2)will do calorimeter test. The tungsten calorimeter will eventually used to calibrate BCM.
3)Learning how the Harp work and how to use it to calibrating BPM.
- Toby:
1) Finish Target filed mapping with Jixie and Chao.
2) Working on analyzing the field mapping data.
- Ryan:
1) Working on Left HRS trigger
2) Will check the material of the target with Josh
- Mellisa:
1) Checking the Cherencov detector in HRS. Try to find how many photon-electron (PHE) each PMT has in the Xgt2 data set.
She need to apply the geometry cut and try again.
- Jie:
1) Analyzing the filed measurement data.
- Jixie:
1) Just Finished the field measurement with help from Chao and Toby. Pengjia and Jie also provide appreciable help.
2) Measured the field in 2 ways. One is measuring the field on the can surface with an axial probe (borrowed
from Josh) fixed in a aluminum block.
http://www.jlab.org/~jixie/HallA/meeting/FieldMeasurement/IMG_0804.JPG
Another is measuring the filed with a 3-axis probe on the translation table.
http://www.jlab.org/~jixie/HallA/meeting/FieldMeasurement/IMG_0800.JPG
The survey group came to the target lab and survey some positions. Just got the survey data yesterday.
Jie and Toby are working on analyzing the field map measurement. Jie is focus on translation table data set
and Toby is working of the can surface data.
3) Talk to Pavel in the Rad. Con. group for the neutron background simulation. Pavel will provide
the neutron distribution and model information such that Jixie will be able to work on radiation calculation.
6/22/2011: Present: Kalyan, Jixie, Chao, Pengjia, Mellisa, Vincent, Ryan, Toby, Alexandre, Jie Liu
- Toby:
1) Tested 4 cables for the slow raster with Ryan
2) Worked with Chao and Jixie to prepare to measure the target field
- Ryan:
1) Continue working on the HRS trigger
- Melissa:
1) Replaying xgt2 data. Looking at the pedestal of adc to find out if there are dead channels
2) Updating the safety document for g2p based on the one used in SANE experiment
- Chao:
1) Preparing a computer in the hall for the DAQ of the 3rd arm 2) Preparing for the target field measurement
- Pengjia:
1) Continue working on the remote control program for the function generator
- Kalyan:
1) Continue designing the 3rd arm
2) Got confirmed from Al that 3rd arm can not be used in GEP
- Jixie:
1) Learning the optics from Nilanga, will meet with Vince to discuss the optics plan
2) Tried to test the magnetize effect of the translation table. Replaced some steel bolts and nuts
with plastic ones. Toby and Chao will make a coil to test the stainless steel.
3) Running simulation to get local beam dump opening for Al. But the HRS transportation routines
from Min do not work.
