Difference between revisions of "Halls A and C Spectrometer Support Group Whiteboard"

From Hall A Wiki
Jump to: navigation, search
(Priority Items)
(21 intermediate revisions by 3 users not shown)
Line 1: Line 1:
 
== Priority Items ==
 
== Priority Items ==
  
Hall A Moller Polarimeter target magnet re-install: target install and survey, compressor and chiller clean up and setup, testing
+
Hall A Moller Polarimeter target magnet testing (Simona's turn when she's ready, and any fixes afterward if necessary)
  
Low voltage connections for BB detectors
+
Install S0 counter above BB for a cosmics trigger.
  
Controls for SBB and corrector coils
+
Locking bar for the Right Shield House (needs to be installed and demonstrated it will keep door closed)
  
Re-tap the SBB supply main transformer for full power
+
Jumper bars for SBB coils (in progress)
  
Connect 480VAC for SBB and corrector power supplies
+
Controls for SBB and corrector coils (waiting for water to the magnets)
  
Ground power supplies and corrector supply racks in DAQ Bunker
+
Install magnet leads for SBB (535 MCM cable) (cables run, waiting on copper bus bars) (connections still need to be torqued)
  
Install magnet leads for SBB (535 MCM cable)
+
Connect magnet leads for SBB corrector magnets (2 AWG welding cable) (cables run, Reagan is making final connections)
  
Install magnet leads for SBB corrector magnets (2 AWG welding cable)
+
re-install ground fault detector in LQ1 supply - requires configuration of module (not started)
  
Connect SBB and corrector magnets to FSD
+
Gas manifolds for GEM gas cylinders (started)
  
Ground HCAL, racks, and support frame
+
Nitrogen supply for GEM gas cylinder valves (Clippard valves and cylinder controller) (not started)
  
Ground racks in DAQ bunker
+
Gas mix controller and MFCs for GEM detectors (not started)
  
re-install ground fault detector in LQ1 supply - requires configuration of module
+
Readout for LCW pressure sensors added at end of beamline walkway (not started)
  
connect power and LCW to BB supply on R-arm platform
+
Re-install crash buttons in Hall A Counting Room - RQ1 button for BB and new ones for SBS supply and correctors (Done, needs tested)
  
Install new liquid level meters on SHMS- Install done, waiting on software and LN2 probe cal to go live (Steve).
+
Install thermistors on SBS/Big Bite magnets and junction boxes. ADC node boards made and parts stuffing is ongoing.
  
Gas manifolds for GEM gas cylinders
+
Install Klixons on SBB and connect to power supply.
  
Nitrogen supply for GEM gas cylinder valves (Clippard valves and cylinder controller)
+
<s>Install Klixons on BB and connect to power supply.</s> Done.
  
Gas mix controller and MFCs for GEM detectors
+
<s>Rpi for threshhold monitoring for DAQ</s> Done.
  
Readout for LCW pressure sensors added at end of beamline walkway
+
Test LQ2 FuG with new polarity reversal switch.
 
+
Re-install crash buttons in Hall A Counting Room - <s>RQ1 button for BB</s> and new ones for SBS supply and correctors
+
  
 +
Verify LQ2 has LCW reconnected.
  
 
== Would Be Good To Do Items ==
 
== Would Be Good To Do Items ==
  
 
Re-locate NDX detectors in Hall A - one in DAQ bunker and the other in BB GEM bunker
 
Re-locate NDX detectors in Hall A - one in DAQ bunker and the other in BB GEM bunker
 +
 +
Roofing material for SBS GEM bunker (located some possible material - will run past Jessie)
  
 
Remove actuators from right arm magnets. (Dipole complete)
 
Remove actuators from right arm magnets. (Dipole complete)
Line 54: Line 55:
 
Remove three Oxford power supplies from HMS
 
Remove three Oxford power supplies from HMS
  
Heaters for SHMS magnet flags./ Guard modifications complete, waiting on controller
+
HMS/SHMS Heater and fan changes, fixes, upgrades etc.
 
+
Heaters for HMS magnet flags-Heaters, modifications to guards complete, heaters installed.  Waiting on controller.
+
 
+
 
+
  
 
== Possible Future Items ==
 
== Possible Future Items ==
Line 65: Line 62:
  
 
Remote reset for Hall C spectrometer motion (maybe next year)
 
Remote reset for Hall C spectrometer motion (maybe next year)
 +
 +
Install new liquid level meters on SHMS- Install done, waiting on software and LN2 probe cal to go live (need Steven).

Revision as of 17:36, 20 September 2021

Priority Items

Hall A Moller Polarimeter target magnet testing (Simona's turn when she's ready, and any fixes afterward if necessary)

Install S0 counter above BB for a cosmics trigger.

Locking bar for the Right Shield House (needs to be installed and demonstrated it will keep door closed)

Jumper bars for SBB coils (in progress)

Controls for SBB and corrector coils (waiting for water to the magnets)

Install magnet leads for SBB (535 MCM cable) (cables run, waiting on copper bus bars) (connections still need to be torqued)

Connect magnet leads for SBB corrector magnets (2 AWG welding cable) (cables run, Reagan is making final connections)

re-install ground fault detector in LQ1 supply - requires configuration of module (not started)

Gas manifolds for GEM gas cylinders (started)

Nitrogen supply for GEM gas cylinder valves (Clippard valves and cylinder controller) (not started)

Gas mix controller and MFCs for GEM detectors (not started)

Readout for LCW pressure sensors added at end of beamline walkway (not started)

Re-install crash buttons in Hall A Counting Room - RQ1 button for BB and new ones for SBS supply and correctors (Done, needs tested)

Install thermistors on SBS/Big Bite magnets and junction boxes. ADC node boards made and parts stuffing is ongoing.

Install Klixons on SBB and connect to power supply.

Install Klixons on BB and connect to power supply. Done.

Rpi for threshhold monitoring for DAQ Done.

Test LQ2 FuG with new polarity reversal switch.

Verify LQ2 has LCW reconnected.

Would Be Good To Do Items

Re-locate NDX detectors in Hall A - one in DAQ bunker and the other in BB GEM bunker

Roofing material for SBS GEM bunker (located some possible material - will run past Jessie)

Remove actuators from right arm magnets. (Dipole complete)

clean up R-arm supply platform

clean up L-arm supply platform

Swap out MFCs in VDC mixing system

Remove three Oxford power supplies from HMS

HMS/SHMS Heater and fan changes, fixes, upgrades etc.

Possible Future Items

Replace air compressor in Hall A Gas Shed (on hold till next fiscal year)

Remote reset for Hall C spectrometer motion (maybe next year)

Install new liquid level meters on SHMS- Install done, waiting on software and LN2 probe cal to go live (need Steven).