Difference between revisions of "Halls A and C Spectrometer Support Group Whiteboard"
| (86 intermediate revisions by 4 users not shown) | |||
| Line 1: | Line 1: | ||
| − | + | == Priority Items == | |
| − | + | Buy and replace MFCs in old FPP mixing system | |
| − | + | Install spring washers on SBB and BB busbars and connections | |
| − | + | Readout for LCW pressure sensors added at end of beamline walkway (not started) | |
| − | + | Replace green LED on Ar/CO2 pre-mix cylinder controller | |
| − | + | Replace right pneumatic valve on Ar/CO2 pre-mix manifold | |
| − | + | Adjust Ar/CO2 mix ratio in old FPP controller to match the pre-mix used for GEMs | |
| + | |||
| + | Replace air compressor in Hall A Gas Shed | ||
| + | |||
| + | Find video cables from hall in the CH | ||
| + | |||
| + | Gas manifolds for GEM gas cylinders (started) | ||
| + | |||
| + | Nitrogen supply for GEM gas cylinder valves (Clippard valves and cylinder controller) (not started) | ||
| + | |||
| + | Gas mix controller and MFCs for GEM detectors (not started) | ||
| + | |||
| + | == Would Be Good To Do Items == | ||
| + | |||
| + | Remove actuators from right arm magnets. (Dipole/Q3 complete) | ||
clean up R-arm supply platform | clean up R-arm supply platform | ||
| Line 17: | Line 31: | ||
clean up L-arm supply platform | clean up L-arm supply platform | ||
| − | + | HMS/SHMS Heater and fan changes, fixes, upgrades etc. | |
| + | |||
| + | Calibrate and op-check spare warm return valves for Hall C. | ||
| + | |||
| + | Setup controls9 | ||
| + | |||
| + | Hall C Moller: setup new chiller, repair compressor, modify bertha | ||
| + | |||
| + | Add bypass switch for SHMS UPS | ||
| + | |||
| + | == PARTS ORDER LIST FOR 1 OCT == | ||
| + | |||
| + | -2 wire cable, | ||
| + | ferrules, | ||
| + | \# 6 hardware | ||
| + | |||
| + | == Do We Still Need To Do These? == | ||
| + | |||
| + | Test LQ2 FuG with new polarity reversal switch. | ||
| + | |||
| + | Mount Left Shield House temperature readout in CH | ||
| + | |||
| + | Find and connect NMR cables in CH | ||
| + | |||
| + | Swap out MFCs in VDC mixing system | ||
| + | |||
| + | == Possible Future Items == | ||
| + | |||
| + | Remote reset for Hall C spectrometer motion (maybe next year) | ||
| − | Install new liquid level meters on SHMS | + | Install new liquid level meters on SHMS- Install done, waiting on software and LN2 probe cal to go live (need Steven). |
Revision as of 19:27, 22 October 2021
Contents
Priority Items
Buy and replace MFCs in old FPP mixing system
Install spring washers on SBB and BB busbars and connections
Readout for LCW pressure sensors added at end of beamline walkway (not started)
Replace green LED on Ar/CO2 pre-mix cylinder controller
Replace right pneumatic valve on Ar/CO2 pre-mix manifold
Adjust Ar/CO2 mix ratio in old FPP controller to match the pre-mix used for GEMs
Replace air compressor in Hall A Gas Shed
Find video cables from hall in the CH
Gas manifolds for GEM gas cylinders (started)
Nitrogen supply for GEM gas cylinder valves (Clippard valves and cylinder controller) (not started)
Gas mix controller and MFCs for GEM detectors (not started)
Would Be Good To Do Items
Remove actuators from right arm magnets. (Dipole/Q3 complete)
clean up R-arm supply platform
clean up L-arm supply platform
HMS/SHMS Heater and fan changes, fixes, upgrades etc.
Calibrate and op-check spare warm return valves for Hall C.
Setup controls9
Hall C Moller: setup new chiller, repair compressor, modify bertha
Add bypass switch for SHMS UPS
PARTS ORDER LIST FOR 1 OCT
-2 wire cable, ferrules, \# 6 hardware
Do We Still Need To Do These?
Test LQ2 FuG with new polarity reversal switch.
Mount Left Shield House temperature readout in CH
Find and connect NMR cables in CH
Swap out MFCs in VDC mixing system
Possible Future Items
Remote reset for Hall C spectrometer motion (maybe next year)
Install new liquid level meters on SHMS- Install done, waiting on software and LN2 probe cal to go live (need Steven).
