Difference between revisions of "Halls A and C Spectrometer Support Group Whiteboard"

From Hall A Wiki
Jump to: navigation, search
(Would Be Good To Do Items)
(95 intermediate revisions by 4 users not shown)
Line 1: Line 1:
Re-install crash buttons in Hall A Counting Room - RQ1 button for BB and new one for SBS supply
+
== Priority Items ==
  
Swap out MFCs in VDC mixing system
+
Readout for LCW pressure sensors added at end of beamline walkway (not started)
  
Remove three Oxford power supplies from HMS
+
Check if optocoupler is missing in LQ2 FuG - Looked for this. Didn't see one on the main boards, but realized as I am writing this, maybe it was for the interface for remote polarity switching? --Ellen
  
<s>HMS Q2 lead voltage drops</s> Done
+
Buy and replace MFCs in old FPP mixing system - MFCs on order
  
Heaters for SHMS magnet flags.
+
Replace air compressor in Hall A Gas Shed - ordered - need to remove old compressor and dryer.
  
Hall A cooldown.
+
Gas manifolds for GEM gas cylinders (started)
  
Heaters for HMS magnet flags-Heaters-modifications to guards complete, heaters installed.  Waiting on controller.
+
Replacement for EEL two cylinder gas cart - ordered, waiting on delivery
  
Help Brad re-configure the DAQ rack in Counting Room C
+
Hall C Moller: setup new chiller, modify bertha, get new helium lines installed when they come in and test magnet cooldown
  
Swap out CAEN HV crate in Counting Room C
+
Nitrogen supply for GEM gas cylinder valves (Clippard valves and cylinder controller) (not started)
  
Controls for SBS corrector coils
+
Gas mix controller and MFCs for GEM detectors (not started)
  
Re-tap the SBS supply main transformer for full power
+
Warm up HB.-Done
  
re-install ground fault detector in LQ1 supply - requires configuration of module
+
Add "T's" and pump out ports to HMS magnet vacuum gauge ports.-Steve didn't want work done.
  
connect power and LCW to BB supply on R-arm platform
+
Add ventilation to SHMS Dipole flow meter shielding.-Done
  
Replace air compressor in Hall A Gas Shed
+
Find 4 atmos leak in Hall C.-In Hall snoop of lines and isolation done.
  
re-locate displays for hacweb11 and 14
+
Move ozone meters from VME to PI.
 +
 
 +
Add fan to beamline side lead (HB)-Done
 +
 
 +
Modify HMS lead heaters, add perforated sheets up stream and add a perforated box downstream to fit heater.-Done
 +
 
 +
== Would Be Good To Do Items ==
 +
 
 +
Remove actuators from right arm magnets. (Dipole/Q3 complete)
  
 
clean up R-arm supply platform
 
clean up R-arm supply platform
Line 33: Line 41:
 
clean up L-arm supply platform
 
clean up L-arm supply platform
  
Install new liquid level meters on SHMS- Install done, waiting on software and LN2 probe cal to go live.
+
HMS/SHMS Heater and fan changes, fixes, upgrades etc.-Done
 
+
Remove actuators from right arm magnets. (Dipole complete)
+
  
<s>HMS supply control boxes into the Shield Hut</s> Done
+
Calibrate and op-check spare warm return valves for Hall C.-Done- new controller for testing and calibration being built.
  
Gas mix controller for GEM detectors
+
Add bypass switch for SHMS UPS - Switch ordered-Done.
  
<s>Fix relay box for HMS counting room E-Stops</s> Done
+
Build local valve control boxes with local read out.
  
Re-locate NDX detectors in Hall A - one in DAQ bunker and the other in BB GEM bunker
+
Build new controller for warm return valves.
  
Readout for LCW pressure sensors added at end of beamline walkway
+
op check/repair hall C vacuum gauges.
  
Remote reset for Hall C spectrometer motion
+
== Do We Still Need To Do These? ==
  
Install new quench protection boards in Hall A LD1
+
== Possible Future Items ==
  
<s>Reconnect Magnet On signs to the HMS supplies</s> Done
+
Remote reset for Hall C spectrometer motion (maybe next year)

Revision as of 07:41, 22 June 2022

Priority Items

Readout for LCW pressure sensors added at end of beamline walkway (not started)

Check if optocoupler is missing in LQ2 FuG - Looked for this. Didn't see one on the main boards, but realized as I am writing this, maybe it was for the interface for remote polarity switching? --Ellen

Buy and replace MFCs in old FPP mixing system - MFCs on order

Replace air compressor in Hall A Gas Shed - ordered - need to remove old compressor and dryer.

Gas manifolds for GEM gas cylinders (started)

Replacement for EEL two cylinder gas cart - ordered, waiting on delivery

Hall C Moller: setup new chiller, modify bertha, get new helium lines installed when they come in and test magnet cooldown

Nitrogen supply for GEM gas cylinder valves (Clippard valves and cylinder controller) (not started)

Gas mix controller and MFCs for GEM detectors (not started)

Warm up HB.-Done

Add "T's" and pump out ports to HMS magnet vacuum gauge ports.-Steve didn't want work done.

Add ventilation to SHMS Dipole flow meter shielding.-Done

Find 4 atmos leak in Hall C.-In Hall snoop of lines and isolation done.

Move ozone meters from VME to PI.

Add fan to beamline side lead (HB)-Done

Modify HMS lead heaters, add perforated sheets up stream and add a perforated box downstream to fit heater.-Done

Would Be Good To Do Items

Remove actuators from right arm magnets. (Dipole/Q3 complete)

clean up R-arm supply platform

clean up L-arm supply platform

HMS/SHMS Heater and fan changes, fixes, upgrades etc.-Done

Calibrate and op-check spare warm return valves for Hall C.-Done- new controller for testing and calibration being built.

Add bypass switch for SHMS UPS - Switch ordered-Done.

Build local valve control boxes with local read out.

Build new controller for warm return valves.

op check/repair hall C vacuum gauges.

Do We Still Need To Do These?

Possible Future Items

Remote reset for Hall C spectrometer motion (maybe next year)