Difference between revisions of "Halls A and C Spectrometer Support Group Whiteboard"

From Hall A Wiki
Jump to: navigation, search
(93 intermediate revisions by 3 users not shown)
Line 1: Line 1:
 
== Priority Items ==
 
== Priority Items ==
  
Hall A Moller Polarimeter target magnet re-install: target install and survey, compressor and chiller clean up and setup, testing
+
Replace PLC relay card on SHMS Dipole - spare card is on the 2nd floor
  
Low voltage connections for BB detectors
+
Install 230V -> 115V transformers for +/-15V supplies dying in Hall C Danfysik supplies - transformers ordered
  
power supply for BB hodoscope
+
Readout for LCW pressure sensors added at end of beamline walkway (not started)
  
Roofing material for SBS GEM bunker
+
Replace air compressor in Hall A Gas Shed - ordered - need to remove old compressor and dryer.
  
Jumper bars for SBB coils
+
Gas manifolds for GEM gas cylinders (started)
  
Controls for SBB and corrector coils
+
Nitrogen supply for GEM gas cylinder valves (Clippard valves and cylinder controller) (not started)
  
Re-tap the SBB supply main transformer for full power
+
Gas mix controller and MFCs for GEM detectors (not started)
  
Connect 480VAC for SBB and corrector power supplies
+
Add "T's" and pump out ports to HMS magnet vacuum gauge ports.-Steve didn't want work done.
 
+
Ground power supplies and corrector supply racks in DAQ Bunker
+
 
+
Install magnet leads for SBB (535 MCM cable)
+
 
+
Install magnet leads for SBB corrector magnets (2 AWG welding cable)
+
 
+
Connect SBB and corrector magnets to FSD
+
 
+
Ground HCAL, racks, and support frame
+
 
+
Ground racks in DAQ bunker
+
 
+
re-install ground fault detector in LQ1 supply - requires configuration of module
+
 
+
connect power and LCW to BB supply on R-arm platform
+
 
+
Install new liquid level meters on SHMS- Install done, waiting on software and LN2 probe cal to go live (Steve).
+
 
+
Gas manifolds for GEM gas cylinders
+
 
+
Nitrogen supply for GEM gas cylinder valves (Clippard valves and cylinder controller)
+
 
+
Gas mix controller and MFCs for GEM detectors
+
 
+
Readout for LCW pressure sensors added at end of beamline walkway
+
 
+
Re-install crash buttons in Hall A Counting Room - <s>RQ1 button for BB</s> and new ones for SBS supply and correctors
+
  
 +
Move ozone meters from VME to PI.
  
 
== Would Be Good To Do Items ==
 
== Would Be Good To Do Items ==
  
Re-locate NDX detectors in Hall A - one in DAQ bunker and the other in BB GEM bunker
+
Remove actuators from right arm magnets. (Dipole/Q3 complete)
 
+
Remove actuators from right arm magnets. (Dipole complete)
+
  
 
clean up R-arm supply platform
 
clean up R-arm supply platform
Line 56: Line 27:
 
clean up L-arm supply platform
 
clean up L-arm supply platform
  
Swap out MFCs in VDC mixing system
+
Build new controller for testing and calibration warm return valves for Hall C
  
Remove three Oxford power supplies from HMS
+
Build local valve control boxes with local read out.
  
Heaters for SHMS magnet flags./ Guard modifications complete, waiting on controller
+
op check/repair hall C vacuum gauges.
  
Heaters for HMS magnet flags-Heaters, modifications to guards complete, heaters installed.  Waiting on controller.
+
Re-route the Danfysik extension cables inside the HMS hut - get the excess off the floor
  
 +
Cut and install poly shielding around HVAC controls on the Right HRS
  
 +
== Do We Still Need To Do These? ==
  
 
== Possible Future Items ==
 
== Possible Future Items ==
 
Replace air compressor in Hall A Gas Shed (on hold till next fiscal year)
 
  
 
Remote reset for Hall C spectrometer motion (maybe next year)
 
Remote reset for Hall C spectrometer motion (maybe next year)

Revision as of 12:18, 12 August 2022

Priority Items

Replace PLC relay card on SHMS Dipole - spare card is on the 2nd floor

Install 230V -> 115V transformers for +/-15V supplies dying in Hall C Danfysik supplies - transformers ordered

Readout for LCW pressure sensors added at end of beamline walkway (not started)

Replace air compressor in Hall A Gas Shed - ordered - need to remove old compressor and dryer.

Gas manifolds for GEM gas cylinders (started)

Nitrogen supply for GEM gas cylinder valves (Clippard valves and cylinder controller) (not started)

Gas mix controller and MFCs for GEM detectors (not started)

Add "T's" and pump out ports to HMS magnet vacuum gauge ports.-Steve didn't want work done.

Move ozone meters from VME to PI.

Would Be Good To Do Items

Remove actuators from right arm magnets. (Dipole/Q3 complete)

clean up R-arm supply platform

clean up L-arm supply platform

Build new controller for testing and calibration warm return valves for Hall C

Build local valve control boxes with local read out.

op check/repair hall C vacuum gauges.

Re-route the Danfysik extension cables inside the HMS hut - get the excess off the floor

Cut and install poly shielding around HVAC controls on the Right HRS

Do We Still Need To Do These?

Possible Future Items

Remote reset for Hall C spectrometer motion (maybe next year)