Difference between revisions of "Halls A and C Spectrometer Support Group Whiteboard"
(→Priority Items) |
|||
| (32 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
== Priority Items == | == Priority Items == | ||
| − | + | SBS air compressor maintenance | |
| − | + | Hall C air compressor maintenance | |
| − | + | Oscillator for LN2 level meter | |
| − | Install | + | Install pressure sensor in warm return in ESR for Hall C |
| − | + | Replace/repair dead MAGNET ON signs in Hall C | |
| − | + | BigBite Argon manifold pressure sensor erratic. Need to clean the connections? | |
| − | + | Some of the SBS magnet bus bars have been running hot. Do we need to re-torque them? | |
| − | + | Readout for LCW pressure sensors added at end of beamline walkway (not started) | |
| − | + | Add "T's" and pump out ports to HMS magnet vacuum gauge ports.-Steve didn't want work done. | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
== Would Be Good To Do Items == | == Would Be Good To Do Items == | ||
| Line 37: | Line 27: | ||
clean up L-arm supply platform | clean up L-arm supply platform | ||
| − | + | Build new controller for testing and calibration warm return valves for Hall C | |
| − | + | Build local valve control boxes with local read out. | |
| − | + | op check/repair hall C vacuum gauges. | |
| − | + | Re-route the Danfysik extension cables inside the HMS hut - get the excess off the floor | |
| − | + | Cut and install poly shielding around HVAC controls on the Right HRS | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
== Do We Still Need To Do These? == | == Do We Still Need To Do These? == | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
== Possible Future Items == | == Possible Future Items == | ||
Remote reset for Hall C spectrometer motion (maybe next year) | Remote reset for Hall C spectrometer motion (maybe next year) | ||
| − | |||
| − | |||
Latest revision as of 18:37, 25 April 2023
Contents
Priority Items
SBS air compressor maintenance
Hall C air compressor maintenance
Oscillator for LN2 level meter
Install pressure sensor in warm return in ESR for Hall C
Replace/repair dead MAGNET ON signs in Hall C
BigBite Argon manifold pressure sensor erratic. Need to clean the connections?
Some of the SBS magnet bus bars have been running hot. Do we need to re-torque them?
Readout for LCW pressure sensors added at end of beamline walkway (not started)
Add "T's" and pump out ports to HMS magnet vacuum gauge ports.-Steve didn't want work done.
Would Be Good To Do Items
Remove actuators from right arm magnets. (Dipole/Q3 complete)
clean up R-arm supply platform
clean up L-arm supply platform
Build new controller for testing and calibration warm return valves for Hall C
Build local valve control boxes with local read out.
op check/repair hall C vacuum gauges.
Re-route the Danfysik extension cables inside the HMS hut - get the excess off the floor
Cut and install poly shielding around HVAC controls on the Right HRS
Do We Still Need To Do These?
Possible Future Items
Remote reset for Hall C spectrometer motion (maybe next year)
