Difference between revisions of "HV Control GUI"
From Hall A Wiki
(changed adaq computer name to remove the "l" as they are now adaq1,adaq2) |
(Updated instructions for GSO detector) |
||
| Line 2: | Line 2: | ||
| − | # Log on to '' | + | # Log on to ''aslow@adaqsc'' |
# ''cd slowc'' | # ''cd slowc'' | ||
# ''./hvs BEAMLINE'' | # ''./hvs BEAMLINE'' | ||
| Line 9: | Line 9: | ||
This will start the GUI. Available channels should say "S1, S5, S6, S9, S12". Navigate to the table and select a channel. ''Make sure you know the desired voltage before proceeding.'' Check the box to enable, then click the HV On/Off on the left, if it is not already active. | This will start the GUI. Available channels should say "S1, S5, S6, S9, S12". Navigate to the table and select a channel. ''Make sure you know the desired voltage before proceeding.'' Check the box to enable, then click the HV On/Off on the left, if it is not already active. | ||
| − | + | These Photon Detector channels are for PREX/CREX running conditions: | |
| + | {| class="wikitable" | ||
| + | ! | ||
| + | ! Slot | ||
| + | ! Channel | ||
| + | ! HV | ||
| + | |- | ||
| + | | GSO (PhDetector) | ||
| + | | SL-12 | ||
| + | | CH-11 | ||
| + | | -1700 V | ||
| + | |- | ||
| + | | Side Finger | ||
| + | | SL-6 | ||
| + | | CH-10 | ||
| + | | -xxxx V | ||
| + | |- | ||
| + | | Top Finger | ||
| + | | SL-6 | ||
| + | | CH-11 | ||
| + | | -xxxx V | ||
| + | |} | ||
| + | |||
| + | Return to [[Compton]] | ||
| + | |||
| + | '''OLD INSTRUCTIONS''' | ||
| + | |||
| + | # Log on to ''adev@adaq1'' or ''adev@adaq2''. | ||
| + | # cd slowc | ||
| + | # ./hvs BEAMLINE | ||
| + | Old channel for PbWO4: Slot 12, Channel 11, set to about -1690V. (desired voltage as of 2016-11-10 to 2016-12-31) | ||
Return to [[Compton]] | Return to [[Compton]] | ||
Revision as of 13:20, 23 January 2019
This GUI is used to enable/set particular voltage channels remotely.
- Log on to aslow@adaqsc
- cd slowc
- ./hvs BEAMLINE
This will start the GUI. Available channels should say "S1, S5, S6, S9, S12". Navigate to the table and select a channel. Make sure you know the desired voltage before proceeding. Check the box to enable, then click the HV On/Off on the left, if it is not already active.
These Photon Detector channels are for PREX/CREX running conditions:
| Slot | Channel | HV | |
|---|---|---|---|
| GSO (PhDetector) | SL-12 | CH-11 | -1700 V |
| Side Finger | SL-6 | CH-10 | -xxxx V |
| Top Finger | SL-6 | CH-11 | -xxxx V |
Return to Compton
OLD INSTRUCTIONS
- Log on to adev@adaq1 or adev@adaq2.
- cd slowc
- ./hvs BEAMLINE
Old channel for PbWO4: Slot 12, Channel 11, set to about -1690V. (desired voltage as of 2016-11-10 to 2016-12-31)
Return to Compton
