Jefferson Lab HALL A Logbook for December 11 - All EXCEPT Automatic Entries

  • Main INDEX

    Thursday

  • 361748 12/22/11 14:22  slifer         target position

  • 361747 12/22/11 13:39  slifer         acceptance

  • 361746 12/22/11 07:12  Zhihong Ye     Restricted Access

  • 361745 12/22/11 06:46  Zhihong Ye     RadCon staff smells burning in the hall, but can not see smoke.

  • 361744 12/22/11 06:26  Zhihong Ye     Hall-A Tools Snap-Shot

  • 361743 12/22/11 06:20  Zhihong Ye     RC Report of Dec21 and Dec22

  • 361742 12/22/11 06:07  mhuang         Owl shift summary

  • 361741 12/22/11 06:05  A. Camsonne    Septa power supplies off

  • 361740 12/22/11 06:02  mhuang         Elastic centering summary

  • 361737 12/22/11 05:59  Pengjia        spot++ 64nA rastered

  • 361736 12/22/11 05:59  Zhihong Ye     Beam officially OFF!

  • 361733 12/22/11 05:52  Pengjia        low current run

  • 361726 12/22/11 05:27  Pengjia        spot++ 87nA rastered

  • 361719 12/22/11 05:18  A. Camsonne    Low current runs at higher gain on BCM

  • 361718 12/22/11 05:18  A. Camsonne    Low current runs at higher gain on BCM

  • 361717 12/22/11 05:13  Zhihong Ye     Re: summary on current scan(better format)

  • 361716 12/22/11 05:12 no_name         Re: Summary of Septum Study (Better Format)

  • 361709 12/22/11 05:07  Pengjia        rastered spot++ in 103~200uA

  • 361708 12/22/11 05:03  A. Camsonne    Turned fast raster 2 mm x 2 mm and slow raster to 0.7 V

  • 361695 12/22/11 04:24  A. Camsonne    SEE BPMs not working at 60 nA

  • 361694 12/22/11 04:23  A. Camsonne    BCM gain changed for run 2155 at 60 nA

  • 361691 12/22/11 04:10  A. Camsonne    Increasing gain on BCM receiver for 50 nA run

  • 361690 12/22/11 04:09  A. Camsonne    BCM at 60 nA Low gain

  • 361651 12/22/11 03:01  A. Camsonne    Tungsten calorimeter runs 150 nA Run 2137 run 21225

  • 361648 12/22/11 02:55  A. Camsonne    requested 200 nA

  • 361627 12/22/11 02:27  mhuang         Septa scan focal plane plots

  • 361597 12/22/11 01:31  mhuang         Dip in focal theta distribution still there after removing ears

  • 361564 12/22/11 00:11  zwzhao         swing shift summary

    • Wednesday

  • 361557 12/21/11 23:38  wenbiao        summary on septum study

  • 361556 12/21/11 23:15  zwzhao         general tools snapshot

  • 361555 12/21/11 22:48  zwzhao         beam is down

  • 361544 12/21/11 22:01  wenbiao        summary on current scan

  • 361531 12/21/11 21:13  A. Camsonne    Could not see left edge of target

  • 361513 12/21/11 20:28  A. Camsonne    Asked for position -5 mm on 1H05B X

  • 361510 12/21/11 20:23  A. Camsonne    Spot ++ with +5 mm offset to the right

  • 361507 12/21/11 20:16  A. Camsonne    Asked for X position 1H05B from 0 to +5mm

  • 361500 12/21/11 20:04  A. Camsonne    Right arm still stuck after iocha16 reboot

  • 361499 12/21/11 20:02  A. Camsonne    Rebooting iocha16

  • 361496 12/21/11 19:54  A. Camsonne    Right Dipole still stuck

  • 361495 12/21/11 19:45  videbaek       GEM Test Detector

  • 361494 12/21/11 19:24  zwzhao         going controlled access for about hafl an hour

  • 361485 12/21/11 18:41  Kalyan         Please log the current scan runs

  • 361484 12/21/11 18:41  A. Camsonne    Right arm dipole power supply stuck

  • 361483 12/21/11 18:20  A. Camsonne    Tungsten calorimeter complete 50 nA complete

  • 361478 12/21/11 17:42  A. Camsonne    Start Calorimeter run setup for 50 nA

  • 361475 12/21/11 17:31  M. Cummings    HV Settings

  • 361466 12/21/11 16:00  sarty          Day Shift Summary

  • 361465 12/21/11 15:42  Kalyan         current scan runs  for BCM/Lumi checks

  • 361464 12/21/11 15:35  Kalyan         Lumi high voltage changed for current scan runs

  • 361461 12/21/11 15:14  videbaek       GEM Test Detector

  • 361460 12/21/11 15:12  Zhihong Ye     Lecory HV white alarm

  • 361459 12/21/11 15:08  sarty          Question: John LeRose Quad Settings when using Septa

  • 361458 12/21/11 15:05  sarty          C-elastic quick delta-scan done; change momentum to C-elastic @ 0%

  • 361457 12/21/11 14:39  X. Zheng       Summary of optics (Delta scan) runs from day shift, day 2

  • 361429 12/21/11 13:18  sarty          Finished C inelastic/false-asym table; changing to elastic delta scan

  • 361412 12/21/11 12:27  A. Camsonne    HARP moving but no signal seen

  • 361409 12/21/11 12:17  R. Michaels    inconsistent file sizes on some runs

  • 361408 12/21/11 12:03  A. Camsonne    Tungsten calorimeter complete - Checking HARPs at 1 uA

  • 361403 12/21/11 11:35  slifer         ears

  • 361402 12/21/11 11:19  Fansler        Beamline

  • 361401 12/21/11 11:19  Zhihong Ye     Current Status: Work Done, Harp looks like working, Beam Permit, etc. 

  • 361400 12/21/11 10:58  A. Camsonne    BCM switch back to 1 MHz receiver

  • 361399 12/21/11 10:50  A. Camsonne    BCM receiver pedestal without 10 KHz

  • 361398 12/21/11 09:46  Chao           Thirdarm thresholds

  • 361397 12/21/11 08:57  sarty          Change Momentum + Controlled Acces for Harps

  • 361396 12/21/11 08:42  Zhihong Ye     Control Access to trouble-shooting SuperHarp

  • 361391 12/21/11 08:15  Norum          Carbon Inelastic, False Asymm

  • 361323 12/21/11 04:09  jie            Target out for run #2057~#2063 and #21153~21160

  • 361294 12/21/11 01:46  Chao           Efficiency test of the helicity decoder

  • 361276 12/21/11 00:07  sarty          Swing Shift Summary

    • Tuesday

  • 361269 12/20/11 23:05  videbaek       GEM Test Detector

  • 361265 12/20/11 23:03  sarty          Update + Called for Controlled Access (Stony Brook)

  • 361264 12/20/11 22:53  A. Camsonne    New BCM receiver with 10 KHz receiver in parallel

  • 361263 12/20/11 22:31  mhuang         Scattered e- momentum & variables distribution @ different septa I study from 12/17 runs

  • 361262 12/20/11 22:31  Zhihong Ye     RC Summary of the day

  • 361238 12/20/11 21:13  Zhihong Ye     Please change prescale factors

  • 361237 12/20/11 21:08  sarty          NOTE: last few runs had Target OUT, not C target (Runs 2036-2041/21136-21141)

  • 361228 12/20/11 20:02  sarty          Hall C informs that they will be flipping half-wave plate

  • 361219 12/20/11 18:43  Zhihong Ye     Spot++ for 1uA

  • 361218 12/20/11 18:38  mhuang         Carbon inelastic spectrum and false asymmetry table

  • 361207 12/20/11 17:54  sarty          HRS momenta set for C elastic @ delta=0%

  • 361206 12/20/11 17:51  M. Cummings    Focal Plane for RHRS

  • 361205 12/20/11 17:24  A. Camsonne    Starting tungsten calorimeter setup for 100 nA run

  • 361204 12/20/11 16:40  sarty          Super Harp IOC rebooted...didn't fix problem

  • 361203 12/20/11 16:22  jpchen         shift summary

  • 361202 12/20/11 15:43  Kalyan         Re: Third Arm DAQ Dead Time test

  • 361201 12/20/11 15:27  Chao           Third Arm DAQ Dead Time test

  • 361200 12/20/11 15:25  jie            RUN 2034 target plane variable distribution cut with L.tr.n=1

  • 361199 12/20/11 15:24  jie            RUN 2034 focal plane variable distribution cut with L.tr.n=1

  • 361198 12/20/11 15:20  jie            RUN 2034 focal plane variable distribution 

  • 361197 12/20/11 15:19  jie            RUN 2034 target plane variable distribution 

  • 361196 12/20/11 15:13  jie            RUN 2029 target plane variable distribution 

  • 361195 12/20/11 15:13  jie            RUN 2029 focal plane variable distribution 

  • 361194 12/20/11 15:07  jie            RUN 2029 focal plane variable distribution cut with L.tr.n=1

  • 361193 12/20/11 15:06  jie            RUN 2029 target plane variable distribution cut with L.tr.n=1

  • 361192 12/20/11 15:04  jie            RUN 2025 target plane variable distribution cut with L.tr.n=1

  • 361191 12/20/11 15:04  jie            RUN 2025 focal plane variable distribution cut with L.tr.n=1

  • 361190 12/20/11 15:03  jie            RUN 2021 focal plane variable distribution cut with L.tr.n=1

  • 361189 12/20/11 15:01  jie            RUN 2021 Target plane variable distribution cut with L.tr.n=1

  • 361188 12/20/11 14:56  X. Zheng       Summary of optics (Delta scan) runs from day shift

  • 361185 12/20/11 14:49  RUN 2029 tar   

  • 361184 12/20/11 14:48  RUN 2029 foc   

  • 361179 12/20/11 14:47  RUN 2029 foc   

  • 361178 12/20/11 14:46  RUN 2029 tar   

  • 361165 12/20/11 14:27  RUN 2025 tar   

  • 361164 12/20/11 14:27  RUN 2025 foc   

  • 361163 12/20/11 14:25  RUN 2021 foc   

  • 361161 12/20/11 14:24  RUN 2021 Tar   

  • 361143 12/20/11 13:47  jpchen         changed to elastic@3%

  • 361142 12/20/11 13:42  jie            run 2025 466A target plane variable distributions

  • 361141 12/20/11 13:41  jie            run 2025 466A focal plane variable distributions

  • 361140 12/20/11 13:31  Jie            run 2021 target plane variable distributions

  • 361139 12/20/11 13:29  Jie            run 2021 focal plane variable distributions

  • 361129 12/20/11 13:08  jpchen         changed to elastic @ +2%

  • 361113 12/20/11 12:34  A. Camsonne    MPS BCM not reading out when calorimeter is in, has any cabling been changed ?

  • 361110 12/20/11 12:30  jpchen         Back out BCM calibration. Back to optics run 1%

  • 361107 12/20/11 12:17  jpchen         status 

  • 361106 12/20/11 11:52  A. Camsonne    Calorimeter run at 100 nA

  • 361101 12/20/11 11:36  X. Zheng       slow raster turned ON

  • 361096 12/20/11 11:31  A. Camsonne    Slow raster on at 1.4V amplitude

  • 361095 12/20/11 11:31  A. Camsonne    Starting tungsten calorimeter setup

  • 361092 12/20/11 11:19  frw            target out

  • 361089 12/20/11 11:12  mhuang         focal plane variable distributions

  • 361075 12/20/11 10:24  mhuang         Target plane variables distribution

  • 361072 12/20/11 10:21  X. Zheng       Runs 2009/21109-2011/21111 had Septum 475A

  • 361069 12/20/11 10:12  A. Camsonne    HARP status - not working

  • 361049 12/20/11 09:02  X. Zheng       Fast raster has been ON for all optics runs from 2001/21101 until 2005/21105

  • 361035 12/20/11 08:00  wenbiao        Owl Shift Summary

  • 361013 12/20/11 03:36  R. Zielinski   Dead time scan run sheet

    • Monday

  • 360950 12/19/11 22:35  Glamazdin      Moller polarimeter results

  • 360949 12/19/11 22:30  A. Camsonne    Requested escorted controlled access to setup max HV on HV crate while moller backing up and HRS ramping

  • 360948 12/19/11 22:27  Pengjia        sis3801 problem and end of run problem in left arm fixed

  • 360911 12/19/11 18:28  kelleher       Large Charge Asymmetry

  • 360910 12/19/11 18:23  A. Camsonne    a-onl account vxworks and backup directories set to root ownership

  • 360907 12/19/11 16:16  Chao           Compare the dE vs E plot with simulation

  • 360906 12/19/11 14:03  Kalyan         Thirdarm TS busy is 120us

  • 360905 12/19/11 14:03  M. Cummings    # of good events per run

  • 360904 12/19/11 13:38  A. Camsonne    TS busy third arm

  • 360896 12/19/11 11:57  Techs          Checklist

  • 360893 12/19/11 11:38  Pengjia        sis3801 scaler changed in left arm

  • 360891 12/19/11 11:26  Kalyan/Chao    Thirdarm thresholds and TS busy checks

  • 360882 12/19/11 08:52  Zhihong Ye     Restricted Access

  • 360881 12/19/11 08:00  frw            Owl Shift Summary

  • 360880 12/19/11 07:29  frw            getting ready for access

  • 360874 12/19/11 06:45  frw            changed R-HRS config?

  • 360871 12/19/11 05:58  frw            run aborted

  • 360869 12/19/11 05:47  frw            the lost boot files (continuing saga)

  • 360868 12/19/11 05:39  frw            TS11 hung, run is junk

  • 360858 12/19/11 03:47  frw            magnet settings

  • 360857 12/19/11 03:43  frw            beam position adjusted

  • 360852 12/19/11 03:16  Pengjia        spot++ for newest run

  • 360851 12/19/11 03:10  Pengjia        BPM Calibration Parameter changes

  • 360845 12/19/11 01:45  T. Badman      

  • 360842 12/19/11 01:41  T. Badman      bcm scaler issue on LHRS

    • Sunday

  • 360827 12/18/11 23:51  sarty          Shift Summary: 16:00-23:59

  • 360824 12/18/11 23:20  sarty          Spot_L for (0,0) with raster off (Run 1946)

  • 360823 12/18/11 23:16  sarty          BPM Strip Chart: @ (0,0) for Left Arm Run 1946

  • 360821 12/18/11 23:06  sarty          Changing momenta: Left to Setting 9; Right to Setting 10

  • 360818 12/18/11 22:51  A. Camsonne    Current spot not calibrated yet - Pengjia will update tonight

  • 360817 12/18/11 22:27  adaq           The run# 1943's out put file is g2p_1943.dat.1

  • 360807 12/18/11 21:47  sarty          spot_R for (-1,+1) no rasters

  • 360806 12/18/11 21:44  sarty          spot_L for (-1,+1) raster off (Runs 1943/21063)

  • 360805 12/18/11 21:41  sarty          BPM Strip Chart: (-1,+1) no raster (Runs 1943/21063)

  • 360798 12/18/11 21:03  sarty          spot_R for BPMs @ (-0.9,+1.2); Run 21061 on  right-arm

  • 360797 12/18/11 21:01  Pengjia        bpm calibration picture

  • 360796 12/18/11 20:57  sarty          Changing momentum - setting 8 (carbon inelastics/false-asym plan)

  • 360794 12/18/11 20:55  sarty          BPM stripchart: @ ~ (-1mm, +1mm); Run 21061 on Right

  • 360790 12/18/11 20:31  R.             Deadtime Check (so far)

  • 360787 12/18/11 20:05  sarty          last note on BPMs (for now) - Runs 1940/21060: (x,y)=(+0.6,+1.3)

  • 360783 12/18/11 19:51  sarty          spot_R to go with BPM stripchart (Runs 1937/21059)

  • 360780 12/18/11 19:49  sarty          Spot_L to go with BPM stripchart (Runs 1937/21059)

  • 360779 12/18/11 19:41  sarty          BPM stripchart for next spot++ (Runs 1937/21059; setting 7D)

  • 360776 12/18/11 19:19  A. Camsonne    BPM position

  • 360773 12/18/11 18:52  sarty          Spot++ for right arm (setting 7, fast raster ON)

  • 360772 12/18/11 18:49  sarty          Spott++ for Left Arm (during setting 7, fast raster ON)

  • 360767 12/18/11 18:33  A. Camsonne    Spot ++

  • 360766 12/18/11 18:33  A. Camsonne    Spot ++

  • 360763 12/18/11 17:55  sarty          Changing momentum - setting 7 (carbon inelastics/false-asym plan)

  • 360752 12/18/11 16:45  Pengjia        Left Arm BPM calibration parameter

  • 360751 12/18/11 16:45  Pengjia        Left Arm BPM calibration parameter

  • 360746 12/18/11 16:04  frw            Day Shift Summary

  • 360739 12/18/11 15:48  frw            scratch that: all is as labeled

  • 360728 12/18/11 15:01  frw            raster was left ON for runs 1924 and 21045

  • 360727 12/18/11 14:44  T.Badman       lumi voltages increased

  • 360704 12/18/11 12:25  A. Camsonne    Recreated HAPPEX crates bootfiles

  • 360700 12/18/11 12:16  T.Badman       lumi HV turned on

  • 360699 12/18/11 12:10  frw            status: beam, no DAQ

  • 360697 12/18/11 10:24  frw            AWOL boot config

  • 360696 12/18/11 08:58  frw            status: waiting for beam

  • 360695 12/18/11 08:18  R. Zielinski   Owl Shift Summary

  • 360690 12/18/11 06:32  R. Zielinski   Happex Crate Boot Directory Deleted

  • 360681 12/18/11 05:10  adaq           BPM raw data check

  • 360676 12/18/11 04:56  P.Zhu / A. C   BPM attenuation factor reduced

  • 360675 12/18/11 04:56  pengjia        BPM pedestal run

  • 360661 12/18/11 03:42  R. Zielinski   RHRS S1 Scintillator ADC/TDC Spectrum

  • 360656 12/18/11 03:33  pengjia        BPM pedestal run

  • 360652 12/18/11 03:12  R. Zielinski   LHRS S1 ADC/TDC Plots

  • 360628 12/18/11 01:41  R. Zielinski   Fixed LHRS DAQ Buffered Mode

  • 360612 12/18/11 00:16  A. Camsonne    Requested for controlled access full survey

    • Saturday

  • 360607 12/17/11 23:59  Carlos Munoz   Swing shift summary

  • 360606 12/17/11 23:58  A. Camsonne    prescale directory disappeared

  • 360595 12/17/11 22:59  Aniol          RHRS wrong Quads for 21017 and 21018

  • 360589 12/17/11 22:19  R. Michaels    re: bta not working

  • 360537 12/17/11 20:04  adaq           Half wave plate OUT

  • 360524 12/17/11 19:34  Aniol          r21012 -momentum in flux

  • 360512 12/17/11 18:41  A. Camsonne    Raster size changed to 1.5mm Width and 0.8 mm Heigth

  • 360496 12/17/11 17:51  Pengjia        attenuate ad needed

  • 360477 12/17/11 17:08  Jack(Techs)    LQ2 work done - Late Entry

  • 360474 12/17/11 16:56  kalyan         lumi HV off

  • 360457 12/17/11 16:33  Kalyan         old lumi HV setting

  • 360450 12/17/11 16:14  kelleher       BTA Software Not working

  • 360448 12/17/11 16:09  Zhihong Ye     Day Shift Summary - better format

  • 360447 12/17/11 16:09  Zhihong Ye     Day Shift Summary

  • 360442 12/17/11 14:53  adaq           fast raster size test

  • 360437 12/17/11 14:26  Pengjia        Fast Raster Size test

  • 360436 12/17/11 14:08  V. Sulkosky    Re: High Deadtime in Left Arm

  • 360435 12/17/11 14:08  yuncheng       Correction of the Run 1837 and 1838 seeting for Left HRS

  • 360424 12/17/11 12:16  Zhihong Ye     Fast Raster has  issues?

  • 360423 12/17/11 12:12  Pengjia        High Deadtime in Left Arm

  • 360415 12/17/11 11:33  Zhihong Ye     Carbon target in

  • 360411 12/17/11 11:03  Zhihong Ye     SPOT++

  • 360408 12/17/11 10:35  Zhihong Ye     Change momentum to 1.68GeV/c

  • 360395 12/17/11 08:36  Zhihong Ye     Spot++: about 2.5x2.5

  • 360382 12/17/11 08:01  wenbiao        Owl shift Summary 12/17/2011

  • 360371 12/17/11 06:14  mhuang         distributions at focal plane

  • 360370 12/17/11 06:14  mhuang         distributions at focal plane

  • 360369 12/17/11 06:06  mhuang         Elastic band

  • 360326 12/17/11 00:05  Mitra          Swing shift Summary 12/16/2011

    • Friday

  • 360245 12/16/11 21:31  Chao           3rd Arm E-3R PMT double peak problem is fixed

  • 360233 12/16/11 20:43  Mitra          Beam is back.

  • 360232 12/16/11 20:40  R. Zielinski   Trigger Efficiencies 

  • 360230 12/16/11 20:32  R. Zielinski   S2m 16L no signal fixed and noisy pedestal in S2m 15R

  • 360229 12/16/11 20:27  Chao           Move 3rd arm E plane 3-R PMT signal to TDC ch 8

  • 360228 12/16/11 19:57  A. Camsonne    I meant BCM

  • 360221 12/16/11 19:19  Mitra          Hall in power permit.

  • 360220 12/16/11 19:08  Mitra          Left arm problem is fixed.

  • 360199 12/16/11 16:02  A. Camsonne    Tungsten calorimeter faraday cup cable seems plugged

  • 360198 12/16/11 15:51  A. Camsonne    Upstream BPM signal fixed

  • 360197 12/16/11 15:34  zwzhao         day shift summary

  • 360196 12/16/11 14:54  mhuang         Updated database

  • 360195 12/16/11 14:47  zwzhao         control access started

  • 360194 12/16/11 14:32  zwzhao         LUMI test data

  • 360180 12/16/11 11:49  kelleher@jla   Access at 2:30pm

  • 360175 12/16/11 11:15  J.Butler(Tec   Magnet On Signs (Late Entry)

  • 360172 12/16/11 11:06  kelleher       Coordinating an access

  • 360165 12/16/11 10:32  zwzhao         monitor beam current with IBC1H04CRCUR2 (red)

  • 360156 12/16/11 10:07  zwzhao         beam is back. start LUMI test now

  • 360153 12/16/11 09:54  Jack(Techs)    Work done yesterday

  • 360152 12/16/11 09:47  Jack(Techs)    LQ2 is in LOCAL control

  • 360151 12/16/11 09:41  zwzhao         won't have beam for another hour

  • 360150 12/16/11 09:25  Jack(Techs)    MAGNET ON signs

  • 360147 12/16/11 08:40  M. Cummings    HV alignment

  • 360131 12/16/11 07:51  Reimer         Owl Shift Summary

  • 360098 12/16/11 05:37  M. Cummings    LHRS elastic peak

  • 360069 12/16/11 03:55  Chao           dE vs E on 3rd Arm update

  • 360068 12/16/11 03:51  reimer         NO slow raster

  • 360055 12/16/11 03:11  A. Camsonne    BPM for different positions

  • 360046 12/16/11 02:39  A. Camsonne    Right arm dipole settled at run 20909

  • 360043 12/16/11 02:38  A. Camsonne    Asked for (0.8,1.5) on 1H05B Run 1737 20908

  • 360032 12/16/11 02:11  A. Camsonne    Asked for (-1,1) on 1H05B

  • 360025 12/16/11 01:23  adaq           New BCM receiver gain set for 1 uA

  • 360010 12/16/11 00:03  Mitra          Shift Summary: Swing Shift Summary 12/15/2011

    • Thursday

  • 360007 12/15/11 23:33  Mitra          BTA has problem.

  • 360006 12/15/11 22:24  A. Camsonne    Slow raster turned off

  • 360001 12/15/11 21:49  A. Camsonne    Calorimeter run complete

  • 359998 12/15/11 21:46  A. Camsonne    Slow raster on for calorimeter run

  • 359997 12/15/11 21:27  A. Camsonne    Slow raster on for calorimeter run

  • 359994 12/15/11 21:17  Mitra          Hall A log problem on hacsbc2

  • 359993 12/15/11 21:15  Mitra          Septa momenta set to 481A (second entry)

  • 359992 12/15/11 20:59  Mitra          No beam. RF separation PS has to be fixed.

  • 359991 12/15/11 20:56  A. Camsonne    RF separator IOC down

  • 359990 12/15/11 20:41  A. Camsonne    Beam with slow raster run 1726

  • 359985 12/15/11 20:20  A. Camsonne    FSD for slow raster working

  • 359980 12/15/11 20:15  A. Camsonne    Slow Raster turned on 0.5 V amplitude 

  • 359979 12/15/11 19:51  A. Camsonne    Started to tune beam in Hall A for Slow Raster commissionning

  • 359978 12/15/11 18:53  Mitra          No Beam

  • 359975 12/15/11 15:58  Pengjia        bpm pedestal database update

  • 359974 12/15/11 15:52  kelleher       counting house "buzzer" alarm

  • 359973 12/15/11 15:21  Aniol          swing shift summary

  • 359972 12/15/11 13:51  Kalyan         dE vs E on thirdarm

  • 359971 12/15/11 12:48  Pengjia        spot++ pedestal

  • 359965 12/15/11 11:38  Chao           3rd Arm DAQ busy time test

  • 359963 12/15/11 11:32  Chao           Third Arm threshold changed

  • 359962 12/15/11 11:31  Folts          Tech call in rules

  • 359958 12/15/11 10:39  Fansler/Butl   Left HRS

  • 359957 12/15/11 10:17  T. Badman      replay on adaq resolved

  • 359952 12/15/11 08:23  kelleher       Hall Status

  • 359951 12/15/11 02:46  M. Cummings    Elastic Peak

  • 359950 12/15/11 02:43  slifer         update

  • 359947 12/15/11 02:28  slifer         RHRS momentum

  • 359946 12/15/11 02:26  reimer         Hall  A Tools

  • 359940 12/15/11 02:12  slifer          run 20890

  • 359936 12/15/11 02:02  reimer         MCC will send beam

  • 359927 12/15/11 01:09  Jack(Techs)    Ouch!

    • Wednesday

  • 359920 12/14/11 23:52  Chao           Third Arm DISC threshold changed

  • 359919 12/14/11 23:45  M. Cummings    Elastic peak - with images

  • 359918 12/14/11 23:41  M. Cummings    Elastic Peak

  • 359917 12/14/11 22:51  kelleher       Septum to be reset -- will continue running tonight

  • 359916 12/14/11 22:34  A. Camsonne    Leave septa off for tonight

  • 359914 12/14/11 22:28  A. Camsonne    Left septum power supply fault

  • 359913 12/14/11 22:14  slifer         right septa current incorrect

  • 359904 12/14/11 21:15  Pengjia        changed all adc in roc5 to 13bit

  • 359903 12/14/11 20:58  adaq           spot++

  • 359902 12/14/11 20:58  slifer         Septa current : L480A, R480A

  • 359891 12/14/11 20:08  slifer         Septa current : L600A, R600A

  • 359890 12/14/11 20:05  Pengjia        spot++

  • 359886 12/14/11 19:39  A. Camsonne    Run with tune beam Septa on 480 A

  • 359884 12/14/11 19:35  Aniol          sporadic beam into hall now

  • 359883 12/14/11 19:30  slifer         Septa current

  • 359878 12/14/11 19:14  Ole Hansen     Moved rootfiles

  • 359875 12/14/11 19:06  slifer         Septa current ramped down

  • 359874 12/14/11 18:17  kelleher       Twitter Account

  • 359869 12/14/11 16:55  Aniol          get paper for printer

  • 359868 12/14/11 16:54  slifer         

  • 359867 12/14/11 16:37  Aniol          need run sheets

  • 359866 12/14/11 15:48  Jack(Techs)    Status of the HRS magnets

  • 359865 12/14/11 15:33  Jack(Techs)    Septum magnet controls

  • 359864 12/14/11 14:17  Chao           HV setting for 3rd arm

  • 359863 12/14/11 14:07  Kalyan         High voltage for third arm detector

  • 359862 12/14/11 13:59  brads          Hall cameras are on the web, hacweb1 instructions

  • 359857 12/14/11 12:56  Zhihong Ye     MCC is still tuning the beam

  • 359856 12/14/11 11:46  Zhihong Ye     Beam is back. Tune Beam

  • 359847 12/14/11 11:07  Zhihong Ye     MCC called for beam trip. Need 20mins.

  • 359846 12/14/11 11:04  Fansler        Left Dipole

  • 359845 12/14/11 10:54  slifer         Septa

  • 359844 12/14/11 10:50  R. Michaels    duplicates on adaql1

  • 359843 12/14/11 09:51  Fansler        Septa

  • 359842 12/14/11 09:13  Fansler        Septa

  • 359841 12/14/11 08:55  Fansler        Left Dipole

  • 359840 12/14/11 08:37  R. Michaels    adaql1 data to MSS now

    • Tuesday

  • 359839 12/13/11 23:10  slifer         septa

  • 359838 12/13/11 22:23  R. Michaels    re: 3rd and R-HRS to MSS

  • 359837 12/13/11 22:20  kelleher       Beam Tuning Results -- Owl Shift Cancelled

  • 359832 12/13/11 19:49  kelleher       Spectrometer Settings 

  • 359831 12/13/11 19:26  kelleher       Daily Run Coordinator Update December 13

  • 359830 12/13/11 19:16  A. Camsonne    First channel new BCM saturated

  • 359827 12/13/11 18:06  V. Sulkosky    BPM Strip Chart

  • 359822 12/13/11 17:41  V. Sulkosky    R-HRS and Third Arm Files Not Copying to MSS

  • 359821 12/13/11 17:35  M. Cummings    wide pedestal in S2m 13R

  • 359820 12/13/11 17:32  brads          HV gui software restarted

  • 359819 12/13/11 17:29  M. Cummings    RHRS scaler addresses

  • 359818 12/13/11 17:26  A. Camsonne    Slow raster function generator turned off for beam tune

  • 359817 12/13/11 17:00  R. Michaels    duplicate data files

  • 359816 12/13/11 16:33  Fansler        Tech on Call

  • 359815 12/13/11 16:31  A. Camsonne    Bcm test supply removed

  • 359814 12/13/11 16:31  Fansler        Checklist

  • 359813 12/13/11 16:31  A. Camsonne    Bcm test supply removed

  • 359804 12/13/11 12:01  R. Zielinski   ADC Sync variables

  • 359801 12/13/11 11:22  Kalyan         HVGUI

  • 359797 12/13/11 11:06  brads          Who is screwing with the HV GUI?

  • 359786 12/13/11 08:42  A. Camsonne    [late entry] Bcm new receiver in place

    • Monday

  • 359785 12/12/11 23:48  A. Camsonne    slow raster function generator on halladaq3

  • 359783 12/12/11 21:28  A. Camsonne    Sync ADC module

  • 359781 12/12/11 21:15  R. Zielinski   ADC ROC Sync Cables

  • 359759 12/12/11 16:18  Pengjia        Fast raster & Slow raster in right arm 

  • 359748 12/12/11 11:41  brads          Portscanning is causing problems with the HV crates/GUI...

  • 359744 12/12/11 10:28  R. Michaels    MSS copy / cleanup scripts update

  • 359739 12/12/11 00:30  Pengjia        Fast raster & Slow raster in left arm

    • Sunday

  • 359707 12/11/11 11:58  Pengjia        BeamLine Connection Update

    • Saturday

  • 359690 12/10/11 14:17  Pengjia        BeamLine Connection

    • Friday

  • 359686 12/09/11 20:47  brads          hatsv4:2006 connection was hanging GUI because of telnet connection

  • 359685 12/09/11 18:11  M. Cummings/   RHRS Scaler Addresses Wrong

  • 359684 12/09/11 18:09  Kalyan         How to start beamline HV crate 

  • 359683 12/09/11 17:10  Glamazdin      Moller FSD and IOCHLA

  • 359682 12/09/11 17:10  brads          Plugged 2 new HV cards into Beamline HV crate, slot 11, 12

  • 359680 12/09/11 16:01  M. Cummings/   EDTM Setup for LHRS and RHRS

  • 359679 12/09/11 15:45  V. Sulkosky    Scaler Gates Ready for LHRS and RHRS

  • 359673 12/09/11 14:26  Fansler        Target VME Controls

  • 359672 12/09/11 14:24  Fansler        Target/Septum FSD

  • 359663 12/09/11 12:20  R. Zielinski   Replacement of Cerenkov Logic Units

  • 359662 12/09/11 12:17  R. Zielinski   TA 76 (Shower 76) Signal Cable Moved

  • 359661 12/09/11 12:14  R. Zielisnki   Intel CPU Removed from ROC 1

    • Thursday

  • 359645 12/08/11 19:17  M. Cummings/   R-HRS Datamon

  • 359639 12/08/11 09:16  V. Sulkosky    R-HRS A/C not working

    • Wednesday

  • 359630 12/07/11 21:57  kelleher       hot check out in progress

  • 359627 12/07/11 19:27  V. Sulkosky/   L-HRS Datamon

  • 359618 12/07/11 13:12  Kalyan         Prescale GUI for Left and Right HRS

  • 359616 12/07/11 11:31  A. Camsonne    BPM cabling and test signal

    • Tuesday

    

    Monday
    

  • 359586 12/05/11 19:22  tbadman        start/end of run scripts

  • 359576 12/05/11 16:26  Pengjia        dead time for Right HRS

  • 359574 12/05/11 14:59  R. Zielinski   RHRS VDC Check-out

  • 359565 12/05/11 11:01  Pengjia        happex cpu crash solved

  • 359564 12/05/11 10:54  Pengjia        The problem of arbitration timeout for the intel cpu fastbus gone

  • 359563 12/05/11 10:54  Pengjia        The problem of arbitration timeout for the intel cpu fastbus gone

    • 

    Friday
    

  • 359552 12/02/11 15:44  Pengjia        right arm coda end run fixed

    • 

    Thursday
    

  • 359551 12/01/11 21:58  Pengjia        right arm DAQ status

  • 359547 12/01/11 14:33  Pengjia        Happex crate in left arm

  • 359544 12/01/11 01:34  Pengjia        DAQ test for right arm

    •